UNITED STATES

SECURITIES AND EXCHANGE COMMISSION

Washington, DC 20549

FORM 10-K

For the fiscal year ended December 31, 2023

or

For the transition period from _______ to _________

Commission File No. 001-33624

SINTX Technologies, Inc.

(Exact name of registrant as specified in its charter)

1885 West 2100 South, Salt Lake City, UT 84119

(Address of principal executive offices and Zip Code)

(801) 839-3500

(Registrant’s telephone number, including area code)

Securities registered pursuant to Section 12(b) of the Act:

Securities registered under Section 12(g) of the Act: None

Indicate by check mark if the registrant is a well-known seasoned issuer, as defined in Rule 405 of the Securities Act. Yes ☐ No ☒

Indicate by check mark if the registrant is not required to file reports pursuant to Section 13 or Section 15(d) of the Act. Yes ☐ No ☒

Indicate by check mark whether the registrant (1) has filed all reports required to be filed by Section 13 or 15(d) of the Securities Exchange Act of 1934 during the preceding 12 months (or for such shorter period that the registrant was required to file such reports), and (2) has been subject to such filing requirements for the past 90 days. Yes ☒ No ☐

Indicate by check mark whether the registrant has submitted electronically every Interactive Data File required to be submitted pursuant to Rule 405 of Regulation S-T (§232.405 of this chapter) during the preceding 12 months (or for such shorter period that the registrant was required to submit and post such files). Yes ☒ No ☐

Indicate by check mark whether the registrant is a large accelerated filer, an accelerated filer, a non-accelerated filer, a smaller reporting company, or an emerging growth company. See the definitions of “large accelerated filer,” “accelerated filer,” “smaller reporting company,” and “emerging growth company” in Rule 12b-2 of the Exchange Act.

If an emerging growth company, indicate by check mark if the registrant has elected not to use the extended transition period for complying with any new or revised financial accounting standards provided pursuant to Section 13(a) of the Exchange Act. ☐

Indicate by check mark whether the registrant has filed a report on and attestation to its management’s assessment of the effectiveness of its internal control over financial reporting under Section 404(b) of the Sarbanes-Oxley Act (15 U.S.C. 7262(b)) by the registered public accounting firm that prepared or issued its audit report. ☐

If securities are registered pursuant to Section 12(b) of the Act, indicate by check mark whether the financial statements of the registrant included in the filing reflect the correction of an error to previously issued financial statements. ☐

Indicate by check mark whether any of those error corrections are restatements that required a recovery analysis of incentive-based compensation received by any of the registrant’s executive officers during the relevant recovery period pursuant to §240.10D-1(b). ☐

Indicate by check mark whether the registrant is a shell company (as defined in Rule 12b-2 of the Exchange Act). Yes ☐ No ☒

The aggregate market value of the voting and non-voting common equity held by non-affiliates computed by reference to the price at which the common equity was last sold, or the average bid and asked price of such common equity, as of the last business day of the registrant’s most recently completed second fiscal quarter was $5,175,111.

The number of shares outstanding of the registrant’s common stock, $0.01 par value per share, as of March 11, 2024 was 22,680,139.

DOCUMENTS INCORPORATED BY REFERENCE:

None

TABLE OF CONTENTS

CAUTIONARY NOTE CONCERNING FORWARD-LOOKING STATEMENTS

This Annual Report on Form 10-K contains forward-looking statements within the meaning of the Private Securities Litigation Reform Act of 1995, Section 27A of the Securities Act of 1933, as amended (the “Securities Act”), and Section 21E of the Securities Exchange Act of 1934, as amended (the “Exchange Act”). All statements other than statements of historical fact are forward-looking statements. SINTX Technologies, Inc. (“we”, “us”, “ourselves”, “the Company”) has tried to identify forward-looking statements by using words such as “believe,” “may,” “might,” “could,” “will,” “aim,” “estimate,” “continue,” “anticipate,” “intend,” “expect,” “plan” and similar words. These forward-looking statements are based on our current assumptions, expectations and estimates of future events and trends. Forward-looking statements are only predictions and are subject to many risks, uncertainties and other factors that may affect our businesses and operations and could cause actual results to differ materially from those predicted. These risks and uncertainties include, but are not limited to, factors affecting our quarterly and annual results, our ability to manage our growth, our ability to achieve and sustain profitability, demand for our products, our ability to compete successfully, our ability to rapidly develop and introduce new products, our ability to develop and execute on successful business strategies, our ability to comply with changes and applicable laws and regulations that are applicable to our businesses, our ability to safeguard our intellectual property, our success in defending legal proceedings brought against us, trends in the medical device industry, and general economic conditions, and other risks set forth throughout this Annual Report, including under “Item 1, Business,” “Item 1A, Risk Factors,” and “Item 7, Management’s Discussion and Analysis of Financial Condition and Results of Operations,” and those discussed in other documents we file with the Securities and Exchange Commission (the “SEC”). Moreover, we operate in an evolving environment. New risk factors and uncertainties emerge from time to time and it is not possible for us to predict all risk factors and uncertainties, nor can we assess the impact of all factors on our business or the extent to which any factor, or combination of factors, may cause actual results to differ materially from those contained in any forward-looking statements.

Given these risks and uncertainties, readers are cautioned not to place undue reliance on any forward-looking statements. Forward-looking statements contained in this Annual Report speak only as of the date of this Annual Report. We undertake no obligation to update any forward-looking statements as a result of new information, events or circumstances or other factors arising or coming to our attention after the date hereof.

WHERE YOU CAN FIND MORE INFORMATION

We are subject to the informational requirements of the Exchange Act. Accordingly, we file periodic reports and other information with the SEC. We will make our annual report on Form 10-K, quarterly reports on Form 10-Q, current reports on Form 8-K and amendments to those reports available through our Internet site, https://ir.sintx.com/ as soon as reasonably practicable after electronically filing such materials with the SEC. They may also be obtained free of charge by writing to SINTX Technologies, Inc., Attn: Investor Relations, 1885 West 2100 South, Salt Lake City, UT 84119. In addition, copies of these reports may be obtained through the SEC’s website at www.sec.gov or by visiting the SEC’s Public Reference Room at 100 F Street, NE, Washington, DC 20549 or by calling the SEC at 800-SEC-0330.

Our common stock trades on The NASDAQ Capital Market under the symbol “SINT.”

SUMMARY OF PRINCIPAL RISK FACTORS

Our business operations are subject to numerous risks, factors and uncertainties, including those outside of our control, that could cause our actual results to be harmed, including risks regarding the following:

Risks Related to Our Capital Resources and Impairments

Risks Related to Our Business and Strategy

Risks Related to Regulatory Approval of Our Products and Other Government Regulations

Risks Related to Our Intellectual Property and Litigation

Risks Related to Potential Litigation from Operating Our Business

Risks Related to Public Companies

PART I

Overview – SINTX Technologies

SINTX Technologies is an advanced ceramics company formed in December 1996, focused on providing solutions in a variety of biomedical, technical, and antipathogenic applications. We have grown from focusing primarily on the research, development and commercialization of medical devices manufactured with silicon nitride to becoming an advanced ceramics company engaged in diverse fields, including biomedical, technical and antipathogenic applications. This diversification enables us to focus on our core competencies which are the manufacturing, research, and development of products comprised from advanced ceramic materials for external partners. We seek to connect with new customers, partners and manufacturers to help them realize the goal of leveraging our expertise in advanced ceramics to create new, innovative products across these sectors.

SINTX Core Business

Biomedical Applications: Since its inception, SINTX has been focused on medical grade silicon nitride. SINTX biomedical products have been shown to be biocompatible, bioactive, antipathogenic, and to have superb bone affinity. Spinal implants made from SINTX silicon nitride have been successfully implanted in humans since 2008 in the US, Europe, Brazil, and Taiwan. This established use, along with its inherent resistance to bacterial adhesion and bone affinity suggests that it may also be suitable in other fusion device applications such as arthroplasty implants, foot wedges, and dental implants. Bacterial infection of any biomaterial implants is always a concern. SINTX silicon nitride has been shown to be resistant to bacterial colonization and biofilm formation, making it antibacterial. SINTX silicon nitride products can be polished to a smooth and wear-resistant surface for articulating applications, such as bearings for hip and knee replacements.

We believe that silicon nitride has a superb combination of properties that make it suited for long-term human implantation. Other biomaterials are based on bone grafts, metal alloys, and polymers- all of which have well-known practical limitations and disadvantages. In contrast, silicon nitride has a legacy of success in the most demanding and extreme industrial environments. As a human implant material, silicon nitride offers bone ingrowth, resistance to bacterial and viral infection, ease of diagnostic imaging, resistance to corrosion, and superior strength and fracture resistance, all of which claims are validated in our large and growing inventory of peer-reviewed, published literature reports. We believe that our versatile silicon nitride manufacturing expertise positions us favorably to introduce new and innovative devices in the medical and non-medical fields.

In June 2022, we acquired Technology Assessment and Transfer, Inc. (TA&T), a nearly 40-year-old business with a mission to transition advanced materials and process technologies from a laboratory environment to commercial products and services. TA&T has supplied ceramics for use in several biomedical applications. These products were made via 3D printing and include components for surgical instruments as well as conceptual and prototype dental implants.

Technical Applications: It is our belief that our silicon nitride has the best combination of mechanical, thermal, and electrical properties of any technical ceramic material. It is a high-performance technical ceramic with high strength, toughness, and hardness, and is extremely resistant to thermal shock and impact. It is also an electrically insulating ceramic material. Typically, it is used in applications where high load-bearing capacity, thermal stability, and wear resistance are required. We have obtained AS9100D certification and ITAR registration to facilitate entry into the aerospace and protective armor markets.

We entered the ceramic armor market through the purchase of assets from B4C, LLC and a technology partnership with Precision Ceramics USA. We will develop and manufacture high-performance ceramics for personnel, aircraft, and vehicle armor including a 100% Boron Carbide material for ultimate lightweight performance in ballistic applications, and a composite material made of Boron Carbide and Silicon Carbide for exceptional multi-hit performance against ballistic threats. We have signed a 10-year lease at a building near our headquarters in Salt Lake City, Utah to house development and manufacturing activities for SINTX Armor.

TA&T’s primary area of expertise is material processing and fabrication know-how for a broad spectrum of monolithic ceramic, ceramic composite, and coating materials. Primary technologies include Additive Manufacturing (3D Printing) of ceramics and metals, low-cost fabrication of fiber reinforced ceramic matrix composites (CMCs) and refractory chemical vapor deposited (CVD) coatings, transparent ceramics for ballistic armor and optical applications, and magnetron sputtered (PVD) coatings for lubrication, wear resistance and environmental barrier coatings for CMCs. TA&T also provides a host of services that include 3D printing, PVD-CVD coatings, material processing-CMCs, CIP, PS, HP, HIP, and material characterization for powders and finished parts-TGA/DSC, PSD. SA, Dilatometry, UV-VIS and FTIR transmission, haze and clarity.

Antipathogenic Applications: Today, there is a global need to improve protection against pathogens in everyday life. SINTX believes that by incorporating its unique composition of silicon nitride antipathogenic powder into products such as face masks, filters, and wound care devices, it is possible to manufacture surfaces that inactivate pathogens, thereby limiting the spread of infection and disease. The discovery in 2020 that SINTX silicon nitride inactivates SARS-CoV-2, the virus which causes the disease COVID-19, has opened new markets and applications for our material.

We presently manufacture advanced ceramic powders and components in our manufacturing facilities based in Salt Lake City, Utah.

Our Products

Silicon Nitride

To control the quality, cost and availability of our silicon nitride products and product candidates, we operate our own silicon nitride manufacturing facility. Our 31,000 square foot corporate facility includes an 19,000 square foot FDA registered ISO 13485:2016 certified, and AS9100D certified manufacturing space. It is equipped with state-of-the-art powder processing, spray drying, pressing and computerized machining equipment, sintering furnaces, and other testing equipment that enables us to control the entire manufacturing process for our silicon nitride products and product candidates. All operations with the exception of raw material production are performed in-house. We purchase raw materials, consisting of silicon nitride ceramic powder and dopant chemical compounds, from several vendors which are ISO registered and approved by us. These raw materials are characterized and tested in accordance with our specifications and then blended to formulate our silicon nitride. We believe that there are multiple vendors that can supply us these raw materials and we continually monitor the quality and pricing offered by our vendors to ensure high quality and cost-effective supply of these materials.

The chemical composition of our in-house formulation of silicon nitride and our processing and manufacturing experience allows us to produce silicon nitride in multiple distinct forms. This capability provides us with the ability to utilize our silicon nitride in a variety of ways depending on the intended application, which, together with our silicon nitride’s key characteristics, distinguishes us from other manufacturers of silicon nitride products.

We currently produce silicon nitride for use in our commercial products and product candidates in the following forms:

We believe we are the only FDA-registered and ISO 13485:2016 certified silicon nitride medical device manufacturing facility in the world, and the only provider of structural ceramics-based medical devices used for spinal fusion applications. Silicon nitride is a chemical compound comprised of the element’s silicon and nitrogen, with the chemical formula Si₃N₄. Silicon nitride, an advanced ceramic, is lightweight, resistant to fracture and strong, and is used in many demanding mechanical, thermal and wear applications, such as in space shuttle bearings, jet engine components, and body armor.

We believe our silicon nitride is ideal as an implant material and is superior to other biomaterials currently used in the spine implant market such as PEEK, allograft and autograft bone, metal and traditional oxide ceramics, none of which possess all of the favorable characteristics of silicon nitride:

We and a number of independent third parties have conducted extensive biocompatibility, biomechanical, in vivo and in vitro testing on our silicon nitride composition to establish its safety and efficacy in support of regulatory clearance of our biomaterial, products and product candidates. We have also completed additional testing of our silicon nitride products and product candidates. The results of this testing have been published in over 130 peer reviewed publications and presentations that include basic science studies, small- and large-animal data, and human clinical studies. We believe that our product development strategy is consistent with the manner in which other biomaterials have been successfully introduced into the market and adopted as the standard of care.

Other Advanced Ceramic Products

Ceramic Armor

In 2021, SINTX entered the ceramic armor market through the purchase of assets from B4C, LLC, Dayton, Ohio, and a technology partnership with Precision Ceramics USA. SINTX operates its armor business through its wholly owned subsidiary SINTX Armor, Inc. SINTX will develop and manufacture high-performance ceramics for personnel, aircraft, and vehicle armor including a 100% boron carbide material for ultimate lightweight performance in ballistic applications, and a composite material made of boron carbide and silicon carbide for exceptional multi-hit performance against ballistic threats. The demand for ceramic armor has been propelled in the defense industries and is increasingly being used in the manufacturing of vests, backpacks, and vehicle panels for military applications. Since its introduction during the Vietnam War, ceramic armor has developed into a modern solution for defeating ballistic threats. Armor solutions utilizing ceramics are commonly used to protect vehicles, personnel, aircraft, and marine vessels due to their light weight and high hardness.

Boron carbide has additional uses including wear components – such as nozzles – and as a neutron absorber in nuclear reactors. SINTX is pursuing opportunities in these market segments as well.

We have signed a 10-year lease at a building near our headquarters in Salt Lake City, Utah to house development and manufacturing activities for SINTX Armor. The Company has relocated the B4C assets from Dayton into this facility and has made necessary upgrades to the facility infrastructure to operate the equipment.

A furnace used for our SINTX Armor manufacturing operations overheated and is no longer functional. We have been informed by our insurance carrier that a covered loss has occurred, and coverage is available for the Company’s claim submitted with respect to the sintering furnace that overheated at SINTX Armor in October 2023. The Company will be replacing the damaged furnace and expects the repaired furnace to be up and running in the 4th quarter 2024. Company management continues to work with third parties to temporarily outsource the sintering process.

Technology Assessment and Transfer (“TA&T”)

TA&T’s primary area of expertise is material processing and fabrication know-how for a broad spectrum of monolithic ceramic, ceramic composite, and coating materials. Primary technologies include Additive Manufacturing (3D Printing) of ceramics and metals, low-cost fabrication of fiber reinforced ceramic matrix composites (CMCs) and refractory chemical vapor deposited (CVD) coatings, transparent ceramics for ballistic armor and optical applications, and magnetron sputtered (PVD) coatings for lubrication, wear resistance and environmental barrier coatings for CMCs. TA&T also provides a host of services that include 3D printing, PVD-CVD coatings, material processing-CMCs, CIP, PS, HP, HIP, and material characterization for powders and finished parts-TGA/DSC, PSD. SA, Dilatometry, UV-VIS and FTIR transmission, haze and clarity.

Our Competitive Strengths

We believe we can use our silicon nitride technology platform to become a leading advanced ceramic company and have the following principal competitive strengths:

Our Strategy

Our goal is to become a leading advanced ceramics company. Key elements of our strategy to achieve this goal are the following:

Market Opportunity

Biomedical

We believe our silicon nitride biomaterial technology platform provides us with numerous competitive advantages in the biomaterials market. We manufacture interbody spinal fusion devices for CTL Amedica and have approximately 4 years remaining of a 10-year exclusive right to continue to manufacture them for CTL Amedica. We are developing products on our own behalf and for third party manufacturers – including CTL – for use as components in spine, total hip and knee joint replacements, as well as dental, foot & ankle, and maxillofacial applications. We believe we can also utilize our silicon nitride technology platform to develop future products in additional medical and non-medical markets.

We believe that the main drivers for growth within the orthopedic biomaterials market are the following:

Technical Ceramics

We believe there is significant potential for us to leverage our experience and operational discipline with silicon nitride spinal implants and enter non-medical markets for technical ceramics. The excellent mechanical, electrical, and thermal properties of our silicon nitride make it ideal for highly demanding applications in aerospace, welding, and other industrial applications. Our AS9100D certification and ITAR registration for the silicon nitride factory have allowed us to obtain orders for aerospace components – initially prototype orders which have now become regular production orders. In January 2024 we announced that we entered into a 10-year, Long-Term Agreement (LTA) with a leading manufacturer of aerospace components and systems. Under the LTA, we will manufacture and supply key ceramic aircraft engine components which have been qualified through a rigorous evaluation process. Furthermore, there are few US-based manufacturers of silicon nitride which means there are limited options for those markets that require domestically produced material.

Since announcing our intent to enter the ceramic armor market in 2021, we have received many inquiries for aircraft, vehicle, and body armor. The war in Ukraine has further increased the worldwide need for ceramic armor. Our Salt Lake City armor facility will produce boron carbide and boron carbide/silicon carbide composite armor – materials which are some of the strongest, lightest weight options for ceramic armor. We are developing female-specific torso plates with a partner and expect this market to grow. We also have early-stage relationships with integrators for body armor and aircraft armor.

The acquisition of TA&T has brought well-established relationships with multiple US government agencies to produce new ceramic materials for leading-edge applications in aerospace and energy. TA&T has wide ranging manufacturing capabilities for ceramic coatings, 3D printed ceramics, and transparent ceramic armor. These technologies have been used in over a hundred government research contracts throughout TA&T’s history and are still utilized in the development of novel ceramic-matrix composites. TA&T has entered into a Cooperative Research and Development Agreement (CRADA) with the U.S. Army Combat Capabilities Development Command Army Research Laboratory (DEVCOM ARL). This partnership is expected to leverage the strengths of both organizations in the areas of ceramic additive manufacturing (ceramic 3D printing) and ceramic matrix composites (CMCs). We believe that we can successfully build on TA&T’s legacy, obtain new government contracts, and leverage its wide range of capabilities with materials and manufacturing technologies to increase revenue from non-government sources.

Personal Protective Equipment (PPE)

We believe that there is the opportunity for significant growth in the personal protective equipment or PPE market for products that are shown to have antiviral properties. The Company has demonstrated in controlled research studies the anti-viral properties of its silicon nitride which may be useful in the reduction of the spread of COVID-19 and other pathogens. The study results demonstrated that our unique grade of silicon nitride inactivates the SARS-CoV-2 virus within a minute after exposure and has the potential to decrease the risk of viral disease spread on surfaces. Studies have shown that coronavirus spreads between humans when an infected person coughs or sneezes. Also, the virus can remain active on a variety of commonly touched surfaces for hours to days. We believe that by incorporating our unique composition of silicon nitride into products such as face masks and personal protective equipment, it is possible to manufacture surfaces that inactivate viral particles, thereby limiting the spread of the disease. We envision incorporating our silicon nitride into high-contact surfaces such as medical equipment, screens, countertops, and doorknobs in locations where viral persistence is a concern, such as homes, casinos, and cruise ships. To that effect, we have successfully dispersed and embedded silicon nitride particles into nonwoven and woven fabric fibers.

The first area of focus for application of our unique silicon nitride powder is in face masks and face mask filters. Inclusion of silicon nitride technology into the mask may enhance personal safety while reducing the risk of disease spread. Further applications for this technology include wound care.

Intellectual Property

We rely on a combination of patents, trademarks, trade secrets, nondisclosure agreements, proprietary information ownership agreements and other intellectual property measures to protect our intellectual property rights. We believe that to have a competitive advantage, we must continue to develop and maintain the proprietary aspects of our technologies.

We have fifteen issued U.S. patents, twelve issued foreign patents, fifteen pending U.S. non-provisional patent applications, eighty-one pending foreign applications and one pending PCT patent application. Our first issued patent expired in 2016, with the last of these patents expiring in 2039.

We have three U.S. patents directed to articulating implants using our high-strength, high toughness doped silicon nitride solid ceramic. These issued patents, which include US 7,666,229; US 9,051,639; and US 9,517,136 will expire in November 2023, September 2032, and March 2034, respectively.

We also have one U.S. patent related to our CSC technology that are directed to implants that have both a dense load-bearing, or cortical, component and a porous, or cancellous, component, together with a surface coating. The issued patent US 9,649,197 will expire in July 2035.

In addition, U.S. Patent No. 10,806,831 directed to antibacterial implants and U.S. Patent No. 11,191,787 directed to antipathogenic devices were recently issued which will expire in 2037 and 2039, respectively.

With respect to PCT patent application serial no. PCT/US2018/014781 directed to antibacterial biomedical implants, we entered the national stage in Europe, Australia, Brazil, Canada, China, Japan, Hong Kong, and South Korea as well as one divisional patent application filed in Europe and two divisional applications filed in Japan to seek potential patent protection for our proprietary technologies in those countries.

With respect to PCT patent application serial no. PCT/US2019/026789 directed to methods for improving the wear performance of ceramic-polyethylene or ceramic-ceramic articulation couples utilized in orthopaedic joint prostheses, we entered the national stage in Australia, Brazil, Canada, Europe, Japan, Korea, and Mexico to seek patent protection for our proprietary technologies in those countries.

With respect to PCT application serial no. PCT/US2019/048072 directed to antipathogenic devices and methods, we entered the national stage in Europe, Japan, Mexico, Australia, Brazil, Canada, South Korea, China, and India to seek patent protection for our proprietary technologies in those countries.

With respect to PCT application serial no. PCT/US2020/037170 directed to methods of surface functionalization of zirconia-toughened alumina with silicon nitride, we entered the national stage in Europe, Australia, Brazil, Canada, China, India, Japan, and Mexico to seek patent protection for our proprietary technologies in those countries.

With respect to PCT application serial no. PCT/US2021/014725 directed to antifungal composites and methods thereof, we entered the national stage in Europe, Brazil, Japan, Australia, Canada, China, India, Mexico, and South Korea to seek patent protection for our proprietary technologies in those countries.

With respect to PCT application serial no. PCT/US2021/027258 directed to antipathogenic face mask, we entered the national stage in Australia, Brazil, Canada, China, Europe, India, Japan, South Korea, and Mexico to seek patent protection for our proprietary technologies in those countries.

With respect to PCT application serial no. PCT/US2021/027263 directed to systems and methods for rapid inactivation of SARS-CoV2 by silicon nitride, copper, and aluminum nitride, we entered the national stage in Australia, Brazil, Canada, China, Europe, India, Japan, South Korea, and Mexico to seek patent protection for our proprietary technologies in those countries.

With respect to PCT application serial no. PCT/US2021/038364 directed to antipathogenic devices and methods thereof for antifungal applications, we entered the national stage in Australia, Brazil, Canada, China, Europe, India, Japan, South Korea, and Mexico to seek patent protection for our proprietary technologies in those countries.

With respect to PCT application serial no. PCT/US2021/028975 directed to methods for laser coating of silicon nitride on a metal substrate, we entered the national stage in Australia, Brazil, Canada, China, Europe, India, Japan, South Korea, and Mexico to seek patent protection for our proprietary technologies in those countries.

With respect to PCT application serial no PCT/US2021/028641 directed to methods of silicon nitride laser cladding, we entered the national stage in Australia, Brazil, Canada, China, Europe, India, Japan, South Korea, and Mexico to seek patent protection for our proprietary technologies in those countries.

With respect to PCT application serial no. PCT/US2021/027270 directed to antiviral compositions and devices and methods of use thereof, we entered the national stage in Australia, Brazil, Canada, China, Europe, India, Japan, South Korea, and Mexico to seek patent protection for our proprietary technologies in those countries.

With respect to PCT application serial no. PCT/US2021/056461 directed to systems and methods for selective laser sintering of silicon nitride and metal composites, we entered the national stage in Australia, Brazil, Canada, China, Europe, India, Japan, South Korea, and Mexico to seek patent protection for our proprietary technologies in those countries.

With respect to PCT application serial no. PCT/US2021/056452 directed to systems and methods for hot-isostatic pressing to increase nitrogen content in silicon nitride, we entered the national stage in Australia, Brazil, Canada, China, Europe, India, Japan, South Korea, and Mexico to seek patent protection for our proprietary technologies in those countries.

With respect to PCT application serial no. PCT/US2021/062650 directed to nitride based antipathogenic compositions and devices and method of use thereof, we entered the national stage in Australia, Brazil, Canada, China, Europe, India, Japan, South Korea, and Mexico to seek patent protection for our proprietary technologies in those countries.

With respect to PCT application serial no. PCT/US2022/023868 directed to systems and methods for physical vapor deposition silicon nitride coatings having antimicrobial and osteogenic enhancements, we entered the national stage in Australia, Brazil, Canada, China, Europe, India, Japan, South Korea, and Mexico to seek patent protection for our proprietary technologies in those countries.

In relation to the sale of our spine implant business to CTL Medical under the Asset Purchase Agreement dated September 5, 2018, we assigned our entire right to forty-eight (48) U.S. patents, two (2) foreign patents and three (3) pending patent applications from our patent portfolio to CTL Medical under that transaction. In addition, three (3) U.S. patents (U.S. patent nos. 9,399,309; 9,517,136; and 9,649,197) directed to silicon nitride manufacturing processes were licensed to CTL Medical under an irrevocable, fully paid-up, worldwide license for a ten-year term with CTL Medical also having a Right of First Negotiation to acquire these patents if SINTX decides to later sell these IP assets to a third party.

Our remaining issued patents and pending applications are directed to additional aspects of our products and technologies including, among other things:

We also expect to rely on trade secrets, know-how, continuing technological innovation and in-licensing opportunities to develop and maintain our intellectual property position. However, trade secrets are difficult to protect. We seek to protect the trade secrets in our proprietary technology and processes, in part, by entering into confidentiality agreements with commercial partners, collaborators, employees, consultants, scientific advisors and other contractors and into invention assignment agreements with our employees and some of our commercial partners and consultants. These agreements are designed to protect our proprietary information and, in the case of the invention assignment agreements, to grant us ownership of the technologies that are developed.

Competition

The main alternatives to our silicon nitride biomaterial include: PEEK, which is predominantly manufactured by Invibio; BIOLOX^® delta, which is a traditional oxide ceramic manufactured by CeramTec; allograft bone; metals; and coated metals.

We believe our main competitors in the medical device market, which utilize a variety of competitive biomaterials, include: Medtronic, Inc.; DePuy Synthes Companies, a group of Johnson & Johnson companies; Stryker Corporation; and Zimmer Biomet, Inc. Presently, these companies buy ceramic components on an OEM basis from manufacturers such as CeramTec, Kyocera and CoorsTek, Inc., among others. We anticipate that these and other orthopedic companies and OEMs will seek to introduce new biomaterials and products that compete with ours.

Our main competitors in the technical ceramics market segment include CoorsTek, Kyocera, and Saint Gobain.

Our main competitors in the antipathogenic market segment include BactiGuard and MicroBan.

Competition within our industries is primarily based on technology, innovation, product quality, and product awareness and acceptance by customers. Our principal competitors have substantially greater financial, technical and marketing resources, as well as significantly greater manufacturing capabilities than we do, and they may succeed in developing products that render our products and product candidates non-competitive. Our ability to compete successfully will depend upon our ability to develop innovative products with advanced performance features.

Government Regulation of Medical Devices

Governmental authorities in the United States, at the federal, state and local levels, and other countries extensively regulate, among other things, the research, development, testing, manufacture, labeling, promotion, advertising, distribution, marketing and export and import of products such as those we are commercializing and developing. Failure to obtain approval or clearance to market our products and products under development and to meet the ongoing requirements of these regulatory authorities could prevent us from continuing to market or develop our products and product candidates.

United States

Pre-Marketing Regulation

In the United States, medical devices are regulated by the FDA. Unless an exemption applies, a new medical device will require either prior 510(k) clearance or approval of a premarket approval application, or PMA, before it can be marketed in the United States. The information that must be submitted to the FDA in order to obtain clearance or approval to market a new medical device varies depending on how the medical device is classified by the FDA. Medical devices are classified into one of three classes on the basis of the controls deemed by the FDA to be necessary to reasonably ensure their safety and effectiveness. Class I devices, which are those that have the lowest level or risk associated with them, are subject to general controls, including labeling, premarket notification and adherence to the QSR. Class II devices are subject to general controls and special controls, including performance standards. Class III devices, which have the highest level of risk associated with them, are subject to most of the previously identified requirements as well as to premarket approval. Most Class I devices and some Class II devices are exempt from the 510(k) requirements, although manufacturers of these devices are still subject to registration, listing, labeling and QSR requirements.

A 510(k) premarket notification must demonstrate that the device in question is substantially equivalent to another legally marketed device, or predicate device, that did not require premarket approval. In evaluating the 510(k), the FDA will determine whether the device has the same intended use as the predicate device, and (a) has the same technological characteristics as the predicate device, or (b) has different technological characteristics, and (i) the data supporting the substantial equivalence contains information, including appropriate clinical or scientific data, if deemed necessary by the FDA, that demonstrates that the device is as safe and as effective as a legally marketed device, and (ii) does not raise different questions of safety and effectiveness than the predicate device. Most 510(k)s do not require clinical data for clearance, but the FDA may request such data. The FDA’s goal is to review and act on each 510(k) within 90 days of submission, but it may take longer based on requests for additional information. In addition, requests for additional data, including clinical data, will increase the time necessary to review the notice. If the FDA does not agree that the new device is substantially equivalent to the predicate device, the new device will be classified in Class III, and the manufacturer must submit a PMA. Since July 2012, however, with the enactment of the Food and Drug Administration Safety and Innovation Act, or FDASIA, a de novo pathway is directly available for certain low to moderate risk devices that do not qualify for the 510(k) pathway due to lack of a predicate device. Modifications to a 510(k)-cleared medical device may require the submission of another 510(k) or a PMA if the changes could significantly affect the safety or effectiveness or constitute a major change in the intended use of the device.

Modifications to a 510(k)-cleared device frequently require the submission of a traditional 510(k), but modifications meeting certain conditions may be candidates for FDA review under a Special 510(k). If a device modification requires the submission of a 510(k), but the modification does not affect the intended use of the device or alter the fundamental scientific technology of the device, then summary information that results from the design control process associated with the cleared device can serve as the basis for clearing the application. A Special 510(k) allows a manufacturer to declare conformance to design controls without providing new data. When the modification involves a change in material, the nature of the “new” material will determine whether a traditional or Special 510(k) is necessary. For example, in its Device Advice on How to Prepare a Special 510(k), the FDA uses the example of a change in a material in a finger joint prosthesis from a known metal alloy to a ceramic that has not been used in a legally marketed predicate device as a type of change that should not be submitted as a Special 510(k). However, if the “new” material is a type that has been used in other legally marketed devices within the same classification for the same intended use, a Special 510(k) is appropriate. The FDA gives as an example a manufacturer of a hip implant who changes from one alloy to another that has been used in another legally marketed predicate. Special 510(k)s are typically processed within 30 days of receipt.

The PMA process is more complex, costly and time consuming than the 510(k) clearance procedure. A PMA must be supported by extensive data including, but not limited to, technical, preclinical, clinical, manufacturing, control and labeling information to demonstrate to the FDA’s satisfaction the safety and effectiveness of the device for its intended use. After a PMA is submitted, the FDA has 45 days to determine whether it is sufficiently complete to permit a substantive review. If the PMA is complete, the FDA will file the PMA. The FDA is subject to performance goal review times for PMAs and may issue a decision letter as a first action on a PMA within 180 days of filing, but if it has questions, it will likely issue a first major deficiency letter within 150 days of filing. It may also refer the PMA to an FDA advisory panel for additional review and will conduct a preapproval inspection of the manufacturing facility to ensure compliance with the QSR, either of which could extend the 180-day response target. While the FDA’s ability to meet its performance goals has generally improved during the past few years, it may not meet these goals in the future. A PMA can take several years to complete and there is no assurance that any submitted PMA will ever be approved. Even when approved, the FDA may limit the indication for which the medical device may be marketed or to whom it may be sold. In addition, the FDA may request additional information or request the performance of additional clinical trials before it will reconsider the approval of the PMA or as a condition of approval, in which case the trials must be completed after the PMA is approved. Changes to the device, including changes to its manufacturing process, may require the approval of a supplemental PMA.

If a medical device is determined to present a “significant risk,” the manufacturer may not begin a clinical trial until it submits an investigational device exemption, or IDE, to the FDA and obtains approval of the IDE from the FDA. The IDE must be supported by appropriate data, such as animal and laboratory testing results and include a proposed clinical protocol. These clinical trials are also subject to the review, approval and oversight of an institutional review board, or IRB, which is an independent and multi-disciplinary committee of volunteers who review and approve research proposals, and the reporting of adverse events and experiences, at each institution at which the clinical trial will be performed. The clinical trials must be conducted in accordance with applicable regulations, including but not limited to the FDA’s IDE regulations and current good clinical practices. A clinical trial may be suspended by the FDA, the IRB or the sponsor at any time for various reasons, including a belief that the risks to the study participants outweigh the benefits of participation in the trial. Even if a clinical trial is completed, the results may not demonstrate the safety and efficacy of a device or may be equivocal or otherwise not be sufficient to obtain approval.

Post-Marketing Regulation

After a device is placed on the market, numerous regulatory requirements apply. These include:

Failure to comply with applicable regulatory requirements can result in enforcement action by the FDA, which may include any of the following sanctions:

To ensure compliance with regulatory requirements, medical device manufacturers are subject to market surveillance and periodic, pre-scheduled and unannounced inspections by the FDA, and these inspections may include the manufacturing facilities of our subcontractors.

International Regulation

International sales of medical devices are subject to foreign government regulations, which vary substantially from country to country. The time required to obtain approval by a foreign country may be longer or shorter than that required for FDA approval, and the requirements may differ. For example, the primary regulatory authority with respect to medical devices in Europe is that of the European Union. The European Union consists of 28 countries and has a total population of over 500 million people. The unification of these countries into a common market has resulted in the unification of laws, standards and procedures across these countries, which may expedite the introduction of medical devices like those we are offering and developing. Norway, Iceland, Lichtenstein and Switzerland are not members of the European Union but have transposed applicable European medical device laws into their national legislation. Thus, a device that is marketed in the European Union may also be recognized and accepted in those four non-member European countries as well.

The European Union has adopted numerous directives and standards regulating the design, manufacture, clinical trials, labeling and adverse event reporting for medical devices. Devices that comply with the requirements of relevant directives will be entitled to bear CE Conformity Marking, indicating that the device conforms to the essential requirements of the applicable directives and, accordingly, can be commercially distributed throughout the European Union. Actual implementation of these directives, however, may vary on a country-by-country basis. The CE Mark is a mandatory conformity mark on medical devices distributed and sold in the European Union and certifies that a medical device has met applicable requirements.

The method of assessing conformity varies, but normally involves a combination of self-assessment by the manufacturer and a third-party assessment by a “Notified Body.” Notified Bodies are independent testing houses, laboratories, or product certifiers authorized by the European Union member states to perform the required conformity assessment tasks, such as quality system audits and device compliance testing. An assessment by a Notified Body based within the European Union is required in order for a manufacturer to distribute the product commercially throughout the European Union. Medium and higher risk devices require the intervention of a Notified Body which will be responsible for auditing the manufacturer’s quality system. The Notified Body will also determine whether or not the product conforms to the requirements of the applicable directives. Devices that meet the applicable requirements of E.U. law and have undergone the appropriate conformity assessment routes will be granted CE “certification.” The CE Mark is mandatory for medical devices sold not only within the countries of the European Union but more generally within most of Europe. As many of the European standards are converging with international standards, the CE Mark is often used on medical devices manufactured and sold outside of Europe (notably in Asia that exports many manufactured products to Europe). CE Marking gives companies easier access into not only the European market but also to Asian and Latin American markets, most of whom recognize the CE Mark on medical device as a mark of quality and adhering to international standards of consumer safety, health or environmental requirements.

Compliance with Healthcare Laws

We must comply with various U.S. federal and state laws, rules and regulations pertaining to healthcare fraud and abuse, including anti-kickback and false claims laws, rules, and regulations, as well as other healthcare laws in connection with the commercialization of our products. Fraud and abuse laws are interpreted broadly and enforced aggressively by various state and federal agencies, including the U.S. Department of Justice, the U.S. Office of Inspector General for the Department of Health and Human Services and various state agencies.

We have entered into agreements with certain surgeons for assistance with the design of our products, some of whom we anticipate may make referrals to us or order our products. A majority of these agreements contain provisions for the payments of royalties. In addition, some surgeons currently own shares of our stock. We have structured these transactions with the intention of complying with all applicable laws, including fraud and abuse, data privacy and security, and transparency laws. Despite this intention, there can be no assurance that a particular government agency or court would determine our practices to be in full compliance with such laws. We could be materially impacted if regulatory or enforcement agencies or courts interpret our financial arrangements with surgeons to be in violation of healthcare laws, including, without limitation, fraud and abuse, data privacy and security, or transparency laws.

The U.S. federal Anti-Kickback Statute prohibits persons, including a medical device manufacturer (or a party acting on its behalf), from knowingly or willfully soliciting, receiving, offering or paying remuneration, directly or indirectly, in exchange for or to induce either the referral of an individual for a service or product or the purchasing, ordering, arranging for, or recommending the ordering of, any service or product for which payment may be made by Medicare, Medicaid or any other federal healthcare program. This statute has been interpreted to apply to arrangements between medical device manufacturers on one hand and healthcare providers on the other. The term “remuneration” is not defined in the federal Anti-Kickback Statute and has been broadly interpreted to include anything of value, such as cash payments, gifts or gift certificates, discounts, waiver of payments, credit arrangements, ownership interests, the furnishing of services, supplies or equipment, and the provision of anything at less than its fair market value. Courts have broadly interpreted the scope of the law, holding that it may be violated if merely “one purpose” of an arrangement is to induce referrals, irrespective of the existence of other legitimate purposes. The Anti-Kickback Statute prohibits many arrangements and practices that are lawful in businesses outside of the healthcare industry. Although there are a number of statutory exemptions and regulatory safe harbors protecting certain business arrangements from prosecution, the exemptions and safe harbors are drawn narrowly, and practices that involve remuneration intended to induce prescribing, purchasing or recommending may be subject to scrutiny if they do not qualify for an exemption or safe harbor. Our practices may not in all cases meet all of the criteria for safe harbor protection from federal Anti-Kickback Statute liability. The reach of the Anti-Kickback Statute was broadened by the enacted Patient Protection and Affordable Care Act of 2010 and the Health Care and Education Affordability Reconciliation Act of 2010, collectively, the Affordable Care Act or ACA, which, among other things, amends the intent requirement of the federal Anti-Kickback Statute such that a person or entity no longer needs to have actual knowledge of the statute or specific intent to violate it in order to have committed a violation. In addition, the ACA provides that the government may assert that a claim including items or services resulting from a violation of the federal Anti-Kickback Statute constitutes a false or fraudulent claim for purposes of the federal False Claims Act (discussed below) or the civil monetary penalties statute, which imposes fines against any person who is determined to have presented or caused to be presented claims to a federal healthcare program that the person knows or should know is for an item or service that was not provided as claimed or is false or fraudulent. In addition to the federal Anti-Kickback Statute, many states have their own anti-kickback laws. Often, these laws closely follow the language of the federal law, although they do not always have the same scope, exceptions, safe harbors or sanctions. In some states, these anti-kickback laws apply not only to payments made by government healthcare programs but also to payments made by other third-party payors, including commercial insurance companies.

Sales, marketing, consulting, and advisory arrangements between medical device manufacturers and sales agents and physicians are subject to the Anti-Kickback Statute and other fraud and abuse laws. Government officials have focused recent enforcement efforts on, among other things, the sales and marketing activities of healthcare companies, including medical device manufacturers, and have brought cases against individuals or entities whose personnel allegedly offered unlawful inducements to potential or existing customers in an attempt to procure their business. We expect these activities to continue to be a focus of government enforcement efforts. Settlements of these cases by healthcare companies have involved significant fines and penalties and, in some instances, criminal plea agreements. We are also aware of governmental investigations of some of the largest orthopedic device companies reportedly focusing on consulting and service agreements between these companies and orthopedic surgeons. These developments are ongoing, and we cannot predict the effects they will have on our business.

The federal False Claims Act imposes liability on any person that, among other things, knowingly presents, or causes to be presented, a false or fraudulent claim for payment by a federal healthcare program. The qui tam provisions of the False Claims Act allow a private individual to bring civil actions on behalf of the federal government alleging that the defendant has submitted a false claim, or has caused such a claim to be submitted, to the federal government, and to share in any monetary recovery. There are many potential bases for liability under the False Claims Act. Liability arises, primarily, when a person knowingly submits, or causes another to submit, a false claim for reimbursement to the federal government. The False Claims Act has been used to assert liability on the basis of inadequate care, kickbacks, and other improper referrals, and allegations as to misrepresentations with respect to the services rendered. Qui tam actions have increased significantly in recent years, causing greater numbers of healthcare companies, including medical device manufacturers, to defend false claim actions, pay damages and penalties, or be excluded from participation in Medicare, Medicaid or other federal or state healthcare programs as a result of investigations arising out of such actions. In addition, various states have enacted similar laws analogous to the False Claims Act. Many of these state laws apply where a claim is submitted to any third-party payor and not merely a federal healthcare program. We are unable to predict whether we would be subject to actions under the False Claims Act or a similar state law, or the impact of such actions. However, the cost of defending such claims, as well as any sanctions imposed, could adversely affect our financial performance. The Health Insurance Portability and Accountability Act of 1996, or HIPAA, also created several new federal crimes, including healthcare fraud and false statements relating to healthcare matters. The healthcare fraud statute prohibits knowingly and willfully executing a scheme to defraud any healthcare benefit program, including private third-party payors. The false statements statute prohibits knowingly and willfully falsifying, concealing, or covering up a material fact or making any materially false, fictitious, or fraudulent statement in connection with the delivery of or payment for healthcare benefits, items, or services.

In addition, we may be subject to, or our marketing or research activities may be limited by, data privacy and security regulation by both the federal government and the states in which we conduct our business. For example, HIPAA and its implementing regulations established uniform federal standards for certain “covered entities” (healthcare providers, health plans and healthcare clearinghouses) governing the conduct of certain electronic healthcare transactions and protecting the security and privacy of protected health information. The American Recovery and Reinvestment Act of 2009, commonly referred to as the economic stimulus package, included expansion of HIPAA’s privacy and security standards called the Health Information Technology for Economic and Clinical Health Act, or HITECH, which became effective on February 17, 2010. Among other things, HITECH makes HIPAA’s privacy and security standards directly applicable to “business associates”—independent contractors or agents of covered entities that create, receive, maintain, or transmit protected health information in connection with providing a service for or on behalf of a covered entity. HITECH also increased the civil and criminal penalties that may be imposed against covered entities, business associates and possibly other persons, and gave state attorneys general new authority to file civil actions for damages or injunctions in federal courts to enforce the federal HIPAA laws and seek attorney’s fees and costs associated with pursuing federal civil actions. These laws also require the reporting of breaches of protected health information to affected individuals, regulators and in some cases, local or national media. HIPAA and HITECH impose strict limits on our physician collaborators’ ability to use and disclose patient information on our behalf.

There are also an increasing number of state “sunshine” laws that require manufacturers to provide reports to state governments on pricing and marketing information. Several states have enacted legislation requiring medical device companies to, among other things, establish marketing compliance programs, file periodic reports with the state, make periodic public disclosures on sales and marketing activities, and to prohibit or limit certain other sales and marketing practices. In addition, a federal law known as the Physician Payments Sunshine Act, now requires medical device manufacturers to track and report to the federal government certain payments and other transfers of value made to physicians and teaching hospitals and ownership or investment interests held by physicians and their immediate family members. The first reporting period covered only payments or transfers of value made and ownership or investment interests held by physicians and their immediate family members from August 1, 2013 to December 31, 2013. The federal government disclosed the reported information on a publicly available website beginning in September 2014. For calendar year 2014, the Physician Payments Sunshine Act will require medical device manufacturers to report payments and transfers of values made and ownership or investment interests held by physicians and their immediate family members for the full calendar year. These laws may adversely affect our sales, marketing, and other activities by imposing administrative and compliance burdens on us. If we fail to track and report as required by these laws or to otherwise comply with these laws, we could be subject to the penalty provisions of the pertinent state and federal authorities.

Clinical research is heavily regulated by FDA regulations for the protection of human subjects (21 C.F.R. 50 and 56) and also the regulations of the U.S Department of Health and Human Services, or the Common Rule (45 C.F.R 46). Both FDA human subject regulations and the Common Rule impose restrictions on the involvement of human subjects in clinical research and require, among other things, the balancing of the risks and benefits of research, the documented informed consent of research participants, initial and ongoing review of research by an IRB. Similar regulations govern research conducted in foreign countries. Compliance with human subject protection regulations is costly and time consuming. Failure to comply could substantially and adversely impact our research program and the development of our products.

Because of the breadth of these laws and the narrowness of available statutory and regulatory exemptions, it is possible that some of our business activities could be subject to challenge under one or more of such laws. If our operations are found to be in violation of any of the federal and state laws described above or any other governmental regulations that apply to us, we may be subject to penalties, including criminal and significant civil monetary penalties, damages, fines, imprisonment, exclusion from participation in government healthcare programs, injunctions, recall or seizure of products, total or partial suspension of production, denial or withdrawal of pre-marketing product clearances and approvals, private “qui tam” actions brought by individual whistleblowers in the name of the government or refusal to allow us to enter into supply contracts, including government contracts, and the curtailment or restructuring of our operations. Public disclosure of privacy and data security violations could cause significant reputational harm. Any of these events could adversely affect our ability to operate our business and our results of operations. To the extent that any of our products are sold in a foreign country, we may be subject to similar foreign laws and regulations, which may include, for instance, applicable post-marketing requirements, including safety surveillance, anti-fraud and abuse laws, implementation of corporate compliance programs, as well as laws and regulations requiring transparency of pricing and marketing information and governing the privacy and security of health information, such as the E.U.’s Directive 95/46 on the Protection of Individuals with regard to the Processing of Personal Data, or the Data Directive, and the wide variety of national laws implementing the Data Directive.

Third-Party Reimbursement

Because our customers typically receive payment directly from hospitals and surgical centers, we do not anticipate relying directly on payment for any of our products from third-party payors, such as Medicare, Medicaid, private insurers, and managed care companies. However, our business will be affected by policies administered by federal and state healthcare programs, such as Medicare and Medicaid, as well as private third-party payors, which often follow the policies of the state and federal healthcare programs. For example, our business will be indirectly impacted by the ability of a hospital or medical facility to obtain coverage and third-party reimbursement for procedures performed using our products. Many hospitals and clinics in the United States belong to group purchasing organizations (that typically incentivize their hospital members to make a relatively large proportion of purchases from a limited number of vendors of similar products that have contracted to offer discounted prices). Such contracts often include exceptions for purchasing certain innovative new technologies, however. Accordingly, the commercial success of our products may also depend to some extent on our ability to either negotiate favorable purchase contracts with key group purchasing organizations or persuade hospitals and clinics to purchase our product “off contract.” These third-party payors may deny reimbursement if they determine that a device used in a procedure was not medically necessary; was not used in accordance with cost-effective treatment methods, as determined by the third-party payor; or was used for an unapproved use. A national or local coverage decision denying Medicare coverage for one or more of our products could result in private insurers and other third party payors also denying coverage. Even if favorable coverage and reimbursement status is attained for our products, less favorable coverage policies and reimbursement rates may be implemented in the future. The cost containment measures that third-party payors and providers are instituting, both within the United States and abroad, could significantly reduce our potential revenues from the sale of our products and any product candidates. We cannot provide any assurances that we will be able to obtain and maintain third party coverage or adequate reimbursement for our products and product candidates in whole or in part.

For inpatient and outpatient procedures, including those that will involve use of our products, Medicare and many other third-party payors in the United States reimburse hospitals at a prospectively determined amount. This amount is generally based on one or more diagnosis related groups, or DRGs, associated with the patient’s condition for inpatient treatment and generally based on ambulatory payment classifications, or APCs, associated with the procedures performed as an outpatient at an ambulation surgicenter. Each DRG or APC is associated with a level of payment and may be adjusted from time to time, usually annually. Prospective payments are intended to cover most of the non-physician hospital costs incurred in connection with the applicable diagnosis and related procedures. Implant products, such as those we plan to sell, represent part of the total procedure costs while labor, hospital room and board, and other supplies and services represent the balance of those costs. However, the prospective payment amounts are typically set independently of a particular hospital’s actual costs associated with treating a particular patient and implanting a device. Therefore, the payment that a hospital would receive for a particular hospital visit would not typically take into account the cost of our products.

Medicare has established a number of DRGs for inpatient procedures that involve the use of products similar to ours. Although Medicare has authority to create special DRGs for hospital services that more properly reflect the actual costs of expensive or new-technology devices implanted as part of a procedure, it has declined to do so in the past, and we do not expect that it will do so with respect to our current products and product candidates. Medicare’s DRG and APC classifications may have implications outside of Medicare, as many other U.S. third-party payors often use Medicare DRGs and APCs for purposes of determining reimbursement.

We believe that orthopedic implants generally have been well received by third-party payors because of the ability of these implants to greatly reduce long-term healthcare costs for patients with degenerative joint disease. However, coverage and reimbursement policies vary from payor to payor and are subject to change. As discussed above, hospitals that purchase medical devices for treatment of their patients generally rely on third-party payors to reimburse all or part of the costs and fees associated with the procedures performed with these devices. Both government and private third-party coverage and reimbursement levels are critical to new product acceptance. Neither hospitals nor surgeons are likely to use our products if they do not receive reimbursement for the procedures adequate to cover the cost of our products.

While it is expected that hospitals will be able to obtain coverage for procedures using our products, the level of payment available to them for such procedures may change over time. State and federal healthcare programs, such as Medicare and Medicaid, closely regulate provider payment levels and have sought to contain, and sometimes reduce, payment levels. Commercial insurers and managed care plans frequently follow government payment policies and are likewise interested in controlling increases in the cost of medical care. These third-party payors may deny payment if they determine that a procedure was not medically necessary, a device used in a procedure was not used in accordance with cost-effective treatment methods, as determined by the third-party payor, or was used for an unapproved use. Further, beginning January 1, 2021 and over the course of a three-year period, CMS will eliminate the inpatient only list for Medicare which will result in all spine procedures being payable in the outpatient setting. Reimbursement levels in the hospital outpatient and ASC settings are typically lower than for the hospital inpatient setting and may not be adequate to cover the cost of innovative and novel medical devices.

In addition, some payors are adopting pay-for-performance programs that differentiate payments to healthcare providers based on the achievement of documented quality-of-care metrics, cost efficiencies, or patient outcomes. These programs are intended to provide incentives to providers to find ways to deliver the same or better results while consuming fewer resources. As a result of these programs, and related payor efforts to reduce payment levels, hospitals and other providers are seeking ways to reduce their costs, including the amounts they pay to medical device suppliers. Adverse changes in payment rates by payors to hospitals could adversely impact our ability to market and sell our products and negatively affect our financial performance.

In international markets, healthcare payment systems vary significantly by country and many countries have instituted price ceilings on specific product lines. There can be no assurance that our products will be considered cost-effective by third-party payors, that reimbursement will be available or, if available, that the third-party payors’ reimbursement policies will not adversely affect our ability to sell our products profitably.

Member countries of the European Union offer various combinations of centrally financed healthcare systems and private health insurance systems. The relative importance of government and private systems varies from country to country. Governments may influence the price of medical devices through their pricing and reimbursement rules and control of national healthcare systems that fund a large part of the cost of those products to consumers. Some jurisdictions operate positive and negative list systems under which products may be marketed only once a reimbursement price has been agreed upon. Some of these countries may require, as condition of obtaining reimbursement or pricing approval, the completion of clinical trials that compare the cost-effectiveness of a particular product candidate to currently available therapies. Some E.U. member states allow companies to fix their own prices for devices but monitor and control company profits. The choice of devices is subject to constraints imposed by the availability of funds within the purchasing institution. Medical devices are most commonly sold to hospitals or healthcare facilities at a price set by negotiation between the buyer and the seller. A contract to purchase products may result from an individual initiative or as a result of a competitive bidding process. In either case, the purchaser pays the supplier, and payment terms vary widely throughout the European Union. Failure to obtain favorable negotiated prices with hospitals or healthcare facilities could adversely affect sales of our products.

Employees

As of March 1, 2024, we had 43 employees. We believe that our success will depend, in part, on our ability to attract and retain qualified personnel. We have never experienced a work stoppage due to labor difficulties and believe that our relations with our employees are good. None of our employees are represented by labor unions. We strive toward having a diverse team of employees and are committed to equality, inclusion and workplace diversity.

In addition to the other information contained in this Annual Report, the following risk factors should be considered carefully in evaluating our company. Our business, financial condition, liquidity or results of operations could be materially adversely affected by any of these risks.

Risks Related to Our Capital Resources and Impairments

We will require additional financing and our failure to obtain additional funding would force us to delay, reduce or eliminate our product development programs or commercialization efforts.

We currently have limited committed sources of capital and we have limited liquidity. Our cash and cash equivalents as of December 31, 2023 was $3.3 million. In February 2024 we closed the public offering of $4.0 million of units consisting of shares of common stock, Pre-funded Warrants, Class E Warrants and Class F Warrants, resulting in net proceeds to us of approximately $3.7 million. We expect our current cash and cash equivalents will be sufficient to fund our operations through the second quarter of 2024. We will require substantial future capital in order to continue to continue operating our business, conduct the research and development and regulatory clearance and approval activities necessary to bring our products to market, and to establish effective marketing and sales capabilities. Our existing capital resources are not sufficient to enable us to fund the completion of the development and commercialization of all of our product candidates.

We cannot determine with certainty the duration and completion costs of the current or future development and commercialization of our product candidates for spinal fusion, joint replacement and coated metals or if, when, or to what extent we will generate revenues from the commercialization and sale of any of these product candidates for which we obtain regulatory approval. We may never succeed in achieving regulatory approval for certain or all of these product candidates. The duration, costs and timing of clinical trials and development of our spinal fusion, joint replacement and coated metal product candidates will depend on a variety of factors, including:

A change in the outcome of any of these variables with respect to the development of spinal fusion, joint replacement or coated metal product candidates could mean a significant change in the costs and timing associated with the development of these product candidates.

In addition, if adequate funds to develop our product candidates are not available on a timely basis, we may terminate or delay the development of one or more of our product candidates, or delay activities necessary to commercialize our product candidates. Additional funding may not be available to us on acceptable terms, or at all. Any additional equity financing, if available, may not be available on favorable terms and will most likely be dilutive to our current stockholders, and debt financing, if available, may involve more restrictive covenants. Our ability to access capital when needed is not assured and, if not achieved on a timely basis, will materially harm our business, financial condition and results of operations or could cause us to cease operations.

The timing and amount of our future capital requirements will depend on many factors, including:

Raising additional capital by issuing securities or through debt financings or licensing arrangements will likely cause dilution to existing stockholders, restrict our operations or require us to relinquish proprietary rights.

To the extent that we raise additional capital through the sale of equity or convertible debt securities, your ownership interest will likely be diluted, and the terms may include liquidation or other preferences that adversely affect your rights as a stockholder. Debt financing, if available, may involve agreements that include covenants limiting or restricting our ability to take specific actions such as incurring additional debt, making capital expenditures or declaring dividends. If we raise additional funds through collaboration and licensing arrangements with third parties, we may have to relinquish valuable rights to our technologies or products or grant licenses on terms that are not favorable to us. Any of these events could adversely affect our ability to achieve our product development and commercialization goals and have a material adverse effect on our business, financial condition and results of operations.

Risks Related to Our Business and Strategy

We have incurred net losses since our inception and anticipate that we will continue to incur substantial net losses for the foreseeable future. We may never achieve or sustain profitability.

We have incurred substantial net losses since our inception. For the years ended December 31, 2023 and 2022 we incurred a net loss of $8.3 million and $12.0 million, respectively, and used cash in operations of $14.1 million and $10.3 million, respectively. We have an accumulated deficit of $270.7 and $262.5 million as of December 31, 2023 and 2022 respectively. Our losses have resulted principally from costs incurred in connection with our sales and marketing activities, research and development activities, manufacturing activities, general and administrative expenses associated with our operations, impairments on intangible assets and property and equipment, interest expense, loss on extinguishment of debt and offering costs. Even if we are successful in launching new products into the market, we expect to continue to incur substantial losses for the foreseeable future as we continue to manufacture products for CTL Medical and other OEM customers and research and develop and seek regulatory approvals for our product candidates.

If sales revenue from any of our products or product candidates that receive marketing clearance from the FDA or other regulatory body is insufficient, if we are unable to develop and commercialize any of our product candidates, or if our product development is delayed, we may never become profitable. Even if we do become profitable, we may be unable to sustain or increase our profitability on a quarterly or annual basis.

Our success depends on our ability to successfully commercialize advanced ceramic products for biomedical, industrial, and antipathogenic applications, which to date have experienced only limited market acceptance.

We believe we are the first and only company to use silicon nitride in medical applications. To date, however, we have had limited acceptance of our silicon nitride-based products and prior to the disposition of our spine implant business to CTL, our product revenue was derived substantially from our non-silicon nitride products. In order to succeed in our goal of becoming a leading advanced ceramics company, we must increase market awareness of our silicon nitride interbody spinal fusion products in conjunction with CTL, and develop and launch new biomedical, industrial, and antipathogenic products. If we fail in any of these endeavors or experience delays in pursuing them, we will not generate revenues as planned and will need to curtail operations or seek additional financing earlier than otherwise anticipated.

Our current biomedical products and our future products may not be accepted by hospitals and surgeons and may not become commercially successful.

With the sale of our spine implant business to CTL we are now largely dependent on the efforts of CTL to sell the spinal fusion products that we manufacture and then sell to CTL. If CTL is not able to sell such products or is unable to increase demand for such products, then our revenues will decline. Since obtaining regulatory clearance from the FDA for our first silicon nitride spinal fusion products in 2008, we have not been able to obtain significant market share of the interbody spinal fusion market, and CTL may not obtain such market share in the future. Even if we receive regulatory clearances or approvals for our other product candidates in development, these product candidates may not gain market acceptance among customers.

The orthopedic market is highly competitive, and we may not be able to compete effectively against the larger, well-established companies that dominate this market or emerging and small innovative companies that may seek to obtain or increase their share of the market.

The markets for orthopedic products are intensely competitive, and many of our competitors are much larger and have substantially more financial and human resources than we do. Many have long histories and strong reputations within the industry, and a relatively small number of companies dominate these markets. Medtronic, Inc.; DePuy Synthes Companies, a group of Johnson & Johnson companies; Stryker Corporation; Zimmer-Biomet, Inc.; Zimmer Holdings, Inc.; and Smith & Nephew plc, account for a significant number of orthopedic sales worldwide.

These companies enjoy significant competitive advantages over us, including:

Our products and any product candidates that we may introduce into the market may not enable us to overcome the competitive advantages of these large and dominant orthopedic companies. In addition, even if we successfully introduce additional product candidates incorporating our silicon nitride biomaterial into the market, emerging and small innovative companies may seek to increase their market share and they may eventually possess competitive advantages, which could adversely impact our business. Our competitors may also employ pricing strategies that could adversely affect the pricing of our products and pricing in the spinal fusion and total joint replacement market generally.

Moreover, many other companies are seeking to develop new biomaterials and products which may compete effectively against our products in terms of performance and price. For example, Smith & Nephew has developed a ceramic-coated metal, known as Oxinium, which may overcome certain of the limitations of metal joint replacement products and could directly compete with our silicon nitride and silicon nitride-coated product candidates.

The manufacturing process for our silicon nitride products is complex and requires sophisticated state-of-the-art equipment, experienced manufacturing personnel and highly specialized knowledge. If we are unable to manufacture our silicon nitride products on a timely basis consistent with our quality standards, our results of operation will be adversely impacted.

In order to control the quality, cost and availability of our silicon nitride products, we developed our own manufacturing capabilities. We operate a 31,000 square foot facility which is certified under the ISO 13485 medical device manufacturing standard for medical devices and operates under the FDA’s quality systems regulations, or QSRs. All operations with the exception of raw material production are performed at this facility.

We are the sole manufacturer of our silicon-nitride based products. Our reliance solely on our internal resources to manufacture our silicon nitride products entails risks to which we would not be subject if we had secondary suppliers for their manufacture, including:

Any of these events could lead to a reduction in our product sales, product launch delays, failure to obtain regulatory clearance or approval or impact our ability to successfully sell our products and commercialize our products candidates.

We depend on a limited number of third-party suppliers for key raw materials used in the manufacturing of our silicon nitride products, and the loss of these third-party suppliers or their inability to supply us with adequate raw materials could harm our business.

We rely on a limited number of third-party suppliers for the raw materials required for the production of our silicon nitride products and product candidates. Our dependence on a limited number of third-party suppliers involves several risks, including limited control over pricing, availability, quality, and delivery schedules for raw materials. We have no supply agreements in place with any of our suppliers and cannot be certain that our current suppliers will continue to provide us with the quantities of raw materials that we require or that satisfy our anticipated specifications and quality requirements. Any supply interruption in limited or single sourced raw materials could materially harm our ability to manufacture our products until a new source of supply, if any, could be identified and qualified. We may be unable to find a sufficient alternative supply channel within a reasonable time or on commercially reasonable terms. Any performance failure on the part of our suppliers could delay the production of our silicon nitride products and product candidates and delay the development and commercialization of our product candidates, including limiting supplies necessary for commercial sale, clinical trials and regulatory approvals, which could have a material adverse effect on our business.

In order to be successful, we must expand our available product lines by commercializing new product candidates, but we may not be able to do so in a timely fashion and at expected costs, or at all.

Although we are currently manufacturing silicon nitride interbody spinal fusion implants for CTL, in order to be successful, we will need to expand our product lines to include other advanced ceramic products for both medical and non-medical applications. Therefore, we are developing new manufacturing technologies and new product candidates including our new ceramic armor products. To succeed in our commercialization efforts, we must effectively continue product development and testing, find new strategic partners, obtain regulatory clearances and approvals, and enhance our sales and marketing capabilities. Because of these uncertainties, there is no assurance that we will succeed in bringing any of our current or future product candidates to market. If we fail in bringing our product candidates to market, or experience delays in doing so, we will not generate revenues as planned and will need to curtail operations or seek additional financing earlier than otherwise anticipated.

We will depend on one or more strategic partners to develop and commercialize our biomedical and antipathogenic product candidates, and if our strategic partners are unable to execute effectively on our agreements with them, we may never become profitable.

We are seeking strategic partners to develop and commercialize our biomedical and antipathogenic product candidates. We will be reliant on our strategic partners to develop and commercialize these product candidates, although we have not yet entered into an agreement with any strategic partner to develop products and may be unable to do so on agreeable terms. In order to succeed in our joint commercialization efforts, we and any future partners must execute effectively on all elements of a combined business plan, including continuing to establish sales and marketing capabilities, manage certified, validated and effective commercial-scale manufacturing operations, conduct product development and testing, and obtain regulatory clearances and approvals for our product candidates. If we or any of our strategic partners fail in any of these endeavors, or experience delays in pursuing them, we will not generate revenues as planned and will need to curtail operations or seek additional financing earlier than otherwise anticipated.

Part of our strategy is to establish and develop OEM partnerships and arrangements, which subjects us to various risks.

Because we believe silicon nitride is a superior platform and technology for application in the spine, total joint and other markets and industrial applications, we are establishing OEM partnerships with other companies to replace their materials and products with silicon nitride. Sales of products to OEM customers will expose our business to a number of risks. Sales through OEM partners could be less profitable than direct sales. Sales of our products through multiple channels could also confuse customers and cause the sale of our products to decline. In addition, OEM customers will require that products meet strict standards. Our compliance with these requirements could result in increased development, manufacturing, warranty and administrative costs. A significant increase in these costs could adversely affect our operating results. If we fail to meet OEM specifications on a timely basis, our relationships with our OEM partners may be harmed. Furthermore, we would not control our OEM partners, and they could sell competing products, may not incorporate our technology into their products in a timely manner and may devote insufficient sales efforts to the OEM products.

If hospitals and other healthcare providers are unable to obtain coverage or adequate reimbursement for procedures performed with our products, it is unlikely our products will be widely used.

In the United States, the commercial success of our spinal products will depend, in part, on the extent to which governmental payers at the federal and state levels, including Medicare and Medicaid, private health insurers and other third-party payers provide coverage for and establish adequate reimbursement levels for procedures utilizing our products. Because we typically receive payment directly from the companies for whom we manufacture, we do not anticipate relying directly on payment from third-party payers for our products. However, hospitals and other healthcare providers that purchase orthopedic products manufactured by us from our customers for treatment of their patients generally rely on third-party payers to pay for all or part of the costs and fees associated with our products as part of a “bundled” rate for the associated procedures. The existence of coverage and adequate reimbursement for our products and the procedures performed with them by government and private payers is critical to market acceptance of our existing and future products. Neither hospitals nor surgeons are likely to use our products if they do not receive adequate reimbursement for the procedures utilizing our products.

Many private payers currently base their reimbursement policies on the coverage decisions and payment amounts determined by the Centers for Medicare and Medicaid Services, or CMS, which administers the Medicare program. Others may adopt different coverage or reimbursement policies for procedures performed with our products, while some governmental programs, such as Medicaid, have reimbursement policies that vary from state to state, some of which may not pay for the procedures performed with our products in an adequate amount, if at all. A Medicare national or local coverage decision denying coverage for one or more of our products could result in private and other third-party payers also denying coverage for our products. Third-party payers also may deny reimbursement for our products if they determine that a product used in a procedure was not medically necessary, was not used in accordance with cost-effective treatment methods, as determined by the third-party payer, or was used for an unapproved use. Unfavorable coverage or reimbursement decisions by government programs or private payers underscore the uncertainty that our products face in the market and could have a material adverse effect on our business.

Many hospitals and clinics in the United States belong to group purchasing organizations, which typically incentivize their hospital members to make a relatively large proportion of purchases from a limited number of vendors of similar products that have contracted to offer discounted prices. Such contracts often include exceptions for purchasing certain innovative new technologies, however. Accordingly, the commercial success of our products may also depend to some extent on our ability to either negotiate favorable purchase contracts with key group purchasing organizations and/or persuade hospitals and clinics to purchase our product “off contract.”

The healthcare industry in the United States has experienced a trend toward cost containment as government and private payers seek to control healthcare costs by paying service providers lower rates. While it is expected that hospitals will be able to obtain coverage for procedures using our products, the level of payment available to them for such procedures may change over time. State and federal healthcare programs, such as Medicare and Medicaid, closely regulate provider payment levels and have sought to contain, and sometimes reduce, payment levels. Private payers frequently follow government payment policies and are likewise interested in controlling increases in the cost of medical care. In addition, some payers are adopting pay-for-performance programs that differentiate payments to healthcare providers based on the achievement of documented quality-of-care metrics, cost efficiencies, or patient outcomes. These programs are intended to provide incentives to providers to deliver the same or better results while consuming fewer resources. As a result of these programs, and related payer efforts to reduce payment levels, hospitals and other providers are seeking ways to reduce their costs, including the amounts they pay to medical device manufacturers. We may not be able to sell our implants profitably if third-party payers deny or discontinue coverage or reduce their levels of payment below that which we project, or if our production costs increase at a greater rate than payment levels. Adverse changes in payment rates by payers to hospitals could adversely impact our ability to market and sell these products and negatively affect our financial performance.

In international markets, medical device regulatory requirements and healthcare payment systems vary significantly from country to country, and many countries have instituted price ceilings on specific product lines. We cannot assure you that our products will be considered cost-effective by international third-party payers, that reimbursement will be available or, if available, that the third-party payers’ reimbursement policies will not adversely affect our ability to sell our products profitably. Any failure to receive regulatory or reimbursement approvals would negatively impact market acceptance of our products in any international markets in which those approvals are sought.

There is no assurance that federal or state healthcare reform will not also adversely affect our business and financial results, and we cannot predict how future federal or state legislative, judicial or administrative changes relating to healthcare reform will affect our business.

A pandemic, epidemic or outbreak of an infectious disease in the United States or elsewhere may adversely affect our business.

A significant outbreak in the future of contagious diseases, such as COVID-19, could result in a widespread health crisis that could adversely affect the economies and financial markets of many countries, resulting in an economic downturn. As a result, our ability to raise additional funds, if necessary, may be adversely impacted by risks, or the public perception of the risks, related to the recent outbreak of COVID-19. Furthermore, the third parties we engage, or seek to engage, with respect to OEM manufacturing relationships, and, for supply and development activities, may be adversely impacted by risks, or the public perception of the risks, related to the recent outbreak of COVID-19, which may delay OEM relationships, and, product development opportunities, and increase our costs.

Prolonged negative economic conditions in domestic and international markets may adversely affect us, our suppliers, partners and consumers, and could harm our financial position.

There is a risk that one or more of our current suppliers may not continue to operate. Any lender that is obligated to provide funding to us under any future credit agreement with us may not be able to provide funding in a timely manner, or at all, when we require it. The cost of, or lack of, available credit or equity financing could impact our ability to develop sufficient liquidity to maintain or grow our company. These negative changes in domestic and international economic conditions or additional disruptions of either or both of the financial and credit markets may also affect third-party payers and may have a material adverse effect on our business, results of operations, financial condition and liquidity.

In addition, we believe that various demographics and industry-specific trends will help drive growth in our target markets, but these demographics and trends are uncertain. Actual demand for our products could be significantly less than expected if our assumptions regarding these factors prove to be incorrect or do not materialize.

We are dependent on our senior management team, engineering team, and external advisors, and the loss of any of them could harm our business. We may not have sufficient personnel to effectuate our business strategy due to our recent reduction in force.

The members of our current senior management team may not be able to successfully implement our strategy. In addition, we have not entered into employment agreements, other than change-in-control severance agreements, with any of the members of our senior management team. There are no assurances that the services of any of these individuals will be available to us for any specified period of time. The successful integration of our senior management team, the loss of members of our senior management team, engineering team and key external advisors, or our inability to attract or retain other qualified personnel or advisors could have a material adverse effect on our business, financial condition and results of operations. We may not have sufficient number of qualified personnel to effectuate our business strategy which could have a material adverse effect on our business, financial condition and results of operations.

If we experience significant disruptions in our information technology systems, our business, results of operations and financial condition could be adversely affected.

The efficient operation of our business depends on our information technology systems. We rely on our information technology systems to effectively manage our sales and marketing, accounting and financial functions; manufacturing processes; inventory; engineering and product development functions; and our research and development functions. As such, our information technology systems are vulnerable to damage or interruption including from earthquakes, fires, floods and other natural disasters; terrorist attacks and attacks by computer viruses or hackers; power losses; and computer systems, or Internet, telecommunications or data network failures. The failure of our information technology systems to perform as we anticipate or our failure to effectively implement new systems could disrupt our entire operation and could result in decreased sales, increased overhead costs, excess inventory and product shortages, all of which could have a material adverse effect on our reputation, business, results of operations and financial condition.

Cyber security risks and the failure to maintain the integrity of company, employee or guest data could expose us to data loss, litigation and liability, and our reputation could be significantly harmed.

We collect and third parties collaborating on our clinical trials collect and retain large volumes of data, including personally identifiable information regarding clinical trial participants and others, for business purposes, including for regulatory, research and development and commercialization purposes, and our collaborators’ various information technology systems enter, process, summarize and report such data. We also maintain personally identifiable information about our employees. The integrity and protection of our company, employee and clinical data is critical to our business. We are subject to significant security and privacy regulations, as well as requirements imposed by government regulation. Maintaining compliance with these evolving regulations and requirements could be difficult and may increase our expenses. In addition, a penetrated or compromised data system or the intentional, inadvertent or negligent release or disclosure of data could result in theft, loss or fraudulent or unlawful use of company, employee or clinical data which could harm our reputation, disrupt our operations, or result in remedial and other costs, fines or lawsuits.

Risks Related to Regulatory Approval of Our Products and Other Government Regulations

Contracting with government entities exposes us to additional risks inherent in the government procurement process.

We provide products and services, directly and indirectly, to a variety of domestic government entities, which introduces certain risks, including extended sales and collection cycles, varying governmental budgeting processes and adherence to complex procurement regulations and other government-specific contractual requirements. We have been, are currently and may in the future be subject to audits and investigations relating to our government contracts and any violations could result in various civil and criminal penalties and administrative sanctions, including termination of contracts, payment of fines and suspension or debarment from future government business, as well as harm to our reputation and financial results.

Changes in U.S. government defense spending could negatively impact our financial position, results of operations, liquidity and overall business.

U.S. government sales constitute a portion of our consolidated sales. Our U.S. government revenues largely result from contracts awarded under various U.S. government programs, primarily defense-related programs with the U.S. Department of Defense (DoD). Changes in U.S. government defense spending for various reasons, including as a result of potential changes in policy positions or priorities, could negatively impact our results of operations, financial condition and liquidity. Our programs are subject to U.S. government policies, budget decisions and appropriation processes which are driven by numerous factors including: (1) geopolitical events; (2) macroeconomic conditions; and (3) the ability of the U.S. government to enact relevant legislation, such as appropriations bills. In recent years, U.S. government appropriations have been affected by larger U.S. government budgetary issues and related legislation, and the U.S. government has been unable to complete its budget process before the end of its fiscal year, resulting in both governmental shutdowns and congress providing only enough funds for U.S. government agencies to continue operating at prior-year levels. Further, if the U.S. government debt ceiling is not raised and the national debt reaches the statutory debt ceiling, the U.S. government could default on its debts. As a result, U.S. government defense spending levels are subject to a wide range of outcomes and are difficult to predict beyond the near-term due to numerous factors, including the external threat environment, future governmental priorities and the state of governmental finances. Significant changes in U.S. government defense spending or changes in U.S. government priorities, policies and requirements could have a material adverse effect on our results of operations, financial condition and liquidity.

We design, manufacture and service products that incorporate advanced technologies; the introduction of new products and technologies involves risks and we may not realize the degree or timing of benefits initially anticipated; competition may reduce our revenues and segment share and limit our future opportunities.

We seek to achieve growth through the design, development, production, sale and support of innovative commercial products that incorporate advanced technologies. The product, program and service needs of our customers change and evolve regularly, and we invest substantial amounts in research and development efforts to pursue advancements in a wide range of technologies, products and services. Our ability to realize the anticipated benefits of our technological advancements depends on a variety of factors, including meeting development, production, certification and regulatory approval schedules; receiving regulatory approvals; execution of internal and external performance plans; availability of supplier and internally produced parts and materials; performance of suppliers and subcontractors; availability of supplier and internal facility capacity to perform maintenance, repair and overhaul services on our products; hiring and training of qualified personnel; achieving cost and production efficiencies; identification of emerging technological trends for our target end-customers (such as sustainable technologies, as described below); validation of innovative technologies; risks associated with the development of complex software; the level of customer interest in new technologies and products; and customer acceptance of products we manufacture or that incorporate technologies we develop. In addition, many of our products must adhere to strict regulatory and market-driven safety and performance standards in a variety of jurisdictions. The evolving nature of these standards, along with the long duration of development, production and aftermarket support programs, creates uncertainty regarding program profitability, particularly with our aircraft engine products. Development efforts divert resources from other potential investments in our businesses, and these efforts may not lead to the development of new technologies or products on a timely basis or meet the needs of our customers as fully as competitive offerings. In addition, the industries for our products or products that incorporate our technologies may not develop or grow as we anticipate. We or our customers, suppliers or subcontractors may encounter difficulties in developing and producing new products and services, and may not realize the degree or timing of benefits initially anticipated or may otherwise suffer significant adverse financial consequences. Due to the design complexity of our products or those of our customers or third party manufacturers that incorporate our products into theirs or our customers’ products, we may experience delays in completing the development and introduction of new products or we may experience the suspension of production after these products enter into service due to safety concerns. Delays and/or suspension of production could result in increased development costs or deflect resources from other projects. We operate in highly competitive industries and our competitors may have more extensive or more specialized engineering, manufacturing, marketing and servicing capabilities than we do. Our contracts are typically awarded on a competitive basis. Our bids are based upon, among other items, the cost to provide the products and services. To generate an acceptable return on our investment in these contracts, we must be able to accurately estimate our costs to provide the services and deliver the products and to be able to complete the contracts in a timely manner. If we fail to accurately estimate our costs or the time required to complete a contract, the profitability of our contracts may be materially and adversely affected. Furthermore, our competitors, including our customers, may develop competing technologies which gain industry acceptance in advance of or instead of our products, or meet particular in-demand technological needs before us or with technology that is superior to our existing or new technologies. For example, the enhanced focus on climate change has increased demand for more environmentally sustainable products and services, as described below. Our competitors may develop sustainable products or services that are available to our customers before our products or services, or that are adopted more readily than our products or services. In addition, our competitors or customers might develop new technologies or offerings that might cause our existing technologies and offerings to become obsolete or otherwise decrease demand for our offerings. In addition, the possibility exists that competitors or customers will develop aftermarket services and aftermarket parts for our products that attract customers and adversely impact our return on investment on new products. If we are unable to continue to compete successfully against our current or future competitors in our core businesses, we may experience declines in revenues and industry segment share. Any of the foregoing could have a material adverse effect on our competitive position, results of operations, financial condition or liquidity.

Exports and imports of certain of our products are subject to various export control, sanctions and import regulations and may require authorization from regulatory agencies of the U.S. or other countries.

We must comply with various laws and regulations relating to the export and import of products, services and technology from and into the U.S. and other countries having jurisdiction over our operations. In the U.S., these laws and regulations include, among others, the EAR administered by the U.S. Department of Commerce, the ITAR administered by the U.S. Department of State, embargoes and sanctions regulations administered by the U.S. Department of the Treasury, and import regulations administered by the U.S. Department of Homeland Security and the U.S. Department of Justice. Certain of our products, services and technologies have military or strategic applications and we are required to obtain licenses and authorizations from the appropriate U.S. government agencies before selling these products outside of the U.S. or importing these products into the U.S. U.S. foreign policy or foreign policy of other licensing jurisdictions may affect the licensing process or otherwise prevent us from engaging in business dealings with certain individuals, entities or countries. Any failure by us, our customers or our suppliers to comply with these laws and regulations could result in civil or criminal penalties, fines, seizure of our products, adverse publicity, restrictions on our ability to export or import our products, or the suspension or debarment from doing business with the U.S. government. Moreover, any changes in export control, sanctions or import regulations may further restrict the export of our products or services, and the possibility of such changes requires constant monitoring to ensure we remain compliant. Our ability to obtain required licenses and authorizations on a timely basis or at all is subject to risks and uncertainties, including changing U.S. government foreign policies or laws, delays in Congressional action, or geopolitical and other factors. If we are not successful in obtaining or maintaining the necessary licenses or authorizations in a timely manner, our sales relating to those approvals may be prevented or delayed, and revenue and profit previously recognized may be reversed. Any restrictions on the export or import of our products or product lines could have a material adverse effect on our competitive position, results of operations, financial condition or liquidity.

As a U.S. government contractor, we are subject to risks relating to U.S. government audits, investigations, and disputes.

We are subject to U.S. government investigations relating to our U.S. government contracts. Such U.S. government investigations often take years to complete and could result in administrative, civil or criminal liabilities, including repayments, fines, treble and other damages, forfeitures, restitution or penalties, or could lead to suspension or debarment of U.S. government contracting or of export privileges. For instance, if we or one of our business units were charged with wrongdoing in connection with a U.S. government investigation (including fraud, or violation of certain environmental or export laws, as further described below), the U.S. government could suspend us from bidding on or receiving awards of new U.S. government contracts pending the completion of legal proceedings. If convicted or found liable, the U.S. government could fine and debar us from new U.S. government contracting for a period generally not to exceed three years and could void any contracts found to be tainted by fraud. We also could suffer reputational harm if allegations of impropriety were made against us, even if such allegations are later determined to be unsubstantiated. Further, our U.S. government contracts are subject to audit. An adverse outcome of any audit or investigation could result in civil and criminal penalties and fines, which could negatively impact our results of operations, financial condition and liquidity. In addition, if allegations of impropriety were made against us, we could suffer serious reputational harm, which could negatively affect our financial position, results of operations and liquidity.

Our long-term success depends substantially on our ability to obtain regulatory clearance or approval and thereafter commercialize our product candidates; we cannot be certain that we will be able to do so in a timely manner or at all.

The process of obtaining regulatory clearances or approvals to market a medical device from the FDA or similar regulatory authorities outside of the United States can be costly and time consuming, and there can be no assurance that such clearances or approvals will be granted on a timely basis, or at all. The FDA’s 510(k) clearance process generally takes one to six months from the date of submission, depending on whether a special or traditional 510(k) premarket notification has been submitted, but can take significantly longer. An application for premarket approval, or PMA, must be submitted to the FDA if the device cannot be cleared through the 510(k) clearance process or is not exempt from premarket review by the FDA. The PMA process almost always requires one or more clinical trials and can take two to three years from the date of filing, or even longer. In some cases, including in the case of our interbody spinal fusion devices which incorporate our CSC technology and our solid silicon nitride femoral head component, the FDA requires clinical data as part of the 510(k) clearance process.

It is possible that the FDA could raise questions about spinal fusion products or other medical device product candidates and could require us to perform additional studies on our products and product candidates. Even if the FDA permits us to use the 510(k) clearance process, we cannot assure you that the FDA will not require either supporting data from laboratory tests or studies that we have not conducted, or substantial supporting clinical data. If we are unable to use the 510(k) clearance process for any of our product candidates, are required to provide clinical data or laboratory data that we do not possess to support our 510(k) premarket notifications for any of these product candidates, or otherwise experience delays in obtaining or fail to obtain regulatory clearances, the commercialization of our product candidates in the United States will be delayed or prevented, which will adversely affect our ability to generate additional revenues. It also may result in the loss of potential competitive advantages that we might otherwise attain by bringing our products to market earlier than our competitors. Additionally, although the FDA allows modifications to be made to devices that have received 510(k) clearance with supporting documentation, the FDA may disagree with our decision to modify our cleared devices without submission of a new 510(k) premarket notification, subjecting us to potential product recall, field alerts and corrective actions. Any of these contingencies could adversely affect our business.

Similar to our compliance with U.S. regulatory requirements, we must obtain and comply with international requirements, in order to market and sell our products outside of the United States and we may only promote and market our products, if approved, as permitted by applicable regulatory authorities. There is no guarantee that we will receive the necessary regulatory approvals for our product candidates either inside the United States or internationally. If our product candidates do not receive necessary regulatory approvals, our business could be materially and adversely affected.

The safety of our products is not yet supported by long-term clinical data, and they may prove to be less safe and effective than our laboratory data indicate.

We obtained FDA clearance for each of our spinal fusion products that we currently manufacture for CTL Medical, and we have sought and intend to seek FDA clearance or approval through the FDA’s 510(k) or PMA process and, where applicable, CE marking for our product candidates. The 510(k) clearance process is based on the FDA’s agreement that a new product candidate is substantially equivalent to an already marketed product for which a PMA was not required. While most 510(k) premarket notifications do not require clinical data for clearance, the FDA may request that such data be provided. Long-term clinical data or marketing experience obtained after clearance may indicate that our products cause unexpected complications or other unforeseen negative effects. If this happens, we could be subject to the withdrawal of our marketing clearance and other enforcement sanctions by the FDA or other regulatory authority, product recalls, significant legal liability, significant negative publicity, damage to our reputation and a dramatic reduction in our ability to sell our products, any one of which would have a material adverse effect on our business, financial condition and results of operations.

We may be required to conduct clinical trials to support regulatory approval of some of our product candidates. We have little experience conducting clinical trials, they may proceed more slowly than anticipated, and we cannot be certain that our product candidates will be shown to be safe and effective for human use.

In order to commercialize our product candidates in the United States, we must submit a PMA for some of these product candidates, which will require us to conduct clinical trials. We also plan to provide the FDA with clinical trial data to support some of our 510(k) premarket notifications. We will receive approval or clearance from the FDA to commercialize products requiring a clinical trial only if we can demonstrate to the satisfaction of the FDA, through well-designed and properly conducted clinical trials, that our product candidates are safe and effective and otherwise meet the appropriate standards required for approval or clearance for specified indications.

Clinical trials are complex, expensive, time consuming, uncertain and subject to substantial and unanticipated delays. Before we may begin clinical trials, we must submit and obtain approval for an investigational device exemption, or IDE, that describes, among other things, the manufacture of, and controls for, the device and a complete investigational plan. Clinical trials generally involve a substantial number of patients in a multi-year study. Because we do not have the experience or the infrastructure necessary to conduct clinical trials, we will have to hire one or more contract research organizations, or CROs, to conduct trials on our behalf. CRO contract negotiations may be costly and time consuming and we will rely heavily on the CRO to ensure that our trials are conducted in accordance with regulatory and industry standards. We may encounter problems with our clinical trials and any of those problems could cause us or the FDA to suspend those trials or delay the analysis of the data derived from them.

A number of events or factors, including any of the following, could delay the completion of our clinical trials in the future and negatively impact our ability to obtain FDA approval for, and to introduce our product candidates:

Our clinical trials may need to be redesigned or may not be completed on schedule, if at all. Delays in our clinical trials may result in increased development costs for our product candidates, which could cause our stock price to decline and limit our ability to obtain additional financing. In addition, if one or more of our clinical trials are delayed, competitors may be able to bring products to market before we do, and the commercial viability of our product candidates could be significantly reduced.

Our current and future relationships with third-party payers and current and potential customers in the United States and elsewhere may be subject, directly or indirectly, to applicable anti-kickback, fraud and abuse, false claims, transparency, health information privacy and security and other healthcare laws and regulations, which could expose us to criminal sanctions, civil penalties, contractual damages, reputational harm administrative burdens and diminished profits and future earnings.

Our current and future arrangements with third-party payers and current and potential customers, including providers and physicians, as well as physician owned distributorships or PODs, may expose us to broadly applicable fraud and abuse and other healthcare laws and regulations, including, without limitation, the federal Anti-Kickback Statute and the federal False Claims Act, which may constrain the business or financial arrangements and relationships through which we sell, market and distribute our products. In addition, we may be subject to transparency laws and patient privacy regulations by U.S. federal and state governments and by governments in foreign jurisdictions in which we conduct our business. The applicable federal, state and foreign healthcare laws and regulations that may affect our ability to operate include:

Changes in effective tax rates or adverse outcomes resulting from examination of our income or other tax returns could adversely affect our results of operations and financial condition.

We are subject to taxes by the U.S. federal, state, local and foreign tax authorities, and our tax liabilities will be affected by the allocation of expenses to differing jurisdictions. Our future effective tax rates could be subject to volatility or adversely affected by a number of factors, including:

We may also be subject to audits of our income, sales and other transaction taxes by U.S. federal, state, local and foreign taxing authorities. Outcomes from these audits could have an adverse effect on our operating results and financial condition.

Proposed legislation in the U.S. Congress, including changes in U.S. tax law, and the recently enacted Inflation Reduction Act of 2022 may adversely impact us and the value of common shares, pre-funded warrants, and Warrants.

Changes to U.S. tax laws (which changes may have retroactive application) could adversely affect us or holders of common shares, pre-funded warrants and Warrants. In recent years, many changes to U.S. federal income tax laws have been proposed and made, and additional changes to U.S. federal income tax laws are likely to continue to occur in the future.

The U.S. Congress is currently considering numerous items of legislation which may be enacted prospectively or with retroactive effect, which legislation could adversely impact our financial performance and the value of common shares, pre-funded warrants, and Warrants. Additionally, states in which we operate or own assets may impose new or increased taxes. If enacted, most of the proposals would be effective for the current or later years. The proposed legislation remains subject to change, and its impact on us and holders of common shares, pre-funded warrants, or Warrants is uncertain.

In addition, the Inflation Reduction Act of 2022 was recently signed into law and includes provisions that will impact the U.S. federal income taxation of corporations. Among other items, this legislation includes provisions that will impose a minimum tax on the book income of certain large corporations and an excise tax on certain corporate stock repurchases that would be imposed on the corporation repurchasing such stock. It is unclear how this legislation will be implemented by the U.S. Department of the Treasury and we cannot predict how this legislation or any future changes in tax laws might affect us or holders of common shares, pre-funded warrants or Warrants.

Recently enacted and future legislation may increase the difficulty and cost for us to obtain and monitor regulatory approval or clearance of our product candidates and affect the prices we may obtain for our products.

In the United States and some foreign jurisdictions, there have been a number of legislative and regulatory changes and proposed changes regarding the healthcare system that could prevent or delay clearance and/or approval of our product candidates, restrict or regulate post-clearance and post-approval activities and affect our ability to profitably sell our products and any product candidates for which we obtain marketing approval or clearance.

In addition, FDA regulations and guidance are often revised or reinterpreted by the FDA in ways that may significantly affect our business and our products. Any new regulations or revisions or reinterpretations of existing regulations may impose additional costs or lengthen review times of our products. Delays in receipt of or failure to receive regulatory clearances or approvals for our new products would have a material adverse effect on our business, results of operations and financial condition. In addition, the FDA is currently evaluating the 510(k) process and may make substantial changes to industry requirements, including which devices are eligible for 510(k) clearance, the ability to rescind previously granted 510(k) clearances and additional requirements that may significantly impact the process.

Among policy makers and payers in the United States and elsewhere, there is significant interest in promoting changes in healthcare systems with the stated goals of containing healthcare costs, improving quality and expanding access. In the United States, the medical device industry has been a particular focus of these efforts and has been significantly affected by major legislative initiatives.

We expect that other state and federal healthcare reform measures will be adopted in the future, any of which could reduce the number of patients with coverage or limit the amounts that federal and state governments will pay for healthcare products and services, which could result in reduced demand for our products or additional pricing pressure.

In the European Union and some other international markets, the government provides health care at a low cost to consumers and regulates prices of healthcare products, patient eligibility or reimbursement levels to control costs for the government-sponsored health care system. Many countries are reducing their public expenditures and we expect to see strong efforts to reduce healthcare costs in international markets, including patient access restrictions, suspensions on price increases, prospective and possibly retroactive price reductions and other recoupments and increased mandatory discounts or rebates and recoveries of past price increases. These cost control measures could reduce our revenues. In addition, certain countries set prices by reference to the prices in other countries where our products are marketed. Thus, our inability to secure adequate prices in a particular country may not only limit the marketing of our products within that country but may also adversely affect our ability to obtain acceptable prices in other markets. This may create the opportunity for third-party cross border trade or influence our decision to sell or not to sell a product, thus adversely affecting our geographic expansion plans and revenues.

Risks Related to Our Intellectual Property and Litigation

If the combination of patents, trade secrets and contractual provisions that we rely on to protect our intellectual property is inadequate, our ability to commercialize our products successfully will be harmed, and we may not be able to operate our business profitably.

Our success depends significantly on our ability to protect our proprietary rights to the technologies incorporated in our products. We rely on a combination of patent protection, trade secret laws and nondisclosure, confidentiality and other contractual restrictions to protect our proprietary technology. However, these may not adequately protect our rights or permit us to gain or keep any competitive advantage.

The issuance of a patent is not conclusive as to its scope, validity or enforceability. The scope, validity or enforceability of our issued patents can be challenged in litigation or proceedings before the U.S. Patent and Trademark Office, or the USPTO, or foreign patent offices. In addition, our pending patent applications include claims to numerous important aspects of our products under development that are not currently protected by any of our issued patents. We cannot assure you that any of our pending patent applications will result in the issuance of patents to us. The USPTO or foreign patent offices may deny or require significant narrowing of claims in our pending patent applications. Patents issued as a result of the pending patent applications, if any, may not provide us with significant commercial protection or be issued in a form that is advantageous to us. Proceedings before the USPTO or foreign patent offices could result in adverse decisions as to the priority of our inventions and the narrowing or invalidation of claims in issued patents. The laws of some foreign countries may not protect our intellectual property rights to the same extent as the laws of the United States, if at all.

Our competitors may successfully challenge and invalidate or render unenforceable our issued patents, including any patents that may issue in the future, which could prevent or limit our ability to market our products and could limit our ability to stop competitors from marketing products that are substantially equivalent to ours. In addition, competitors may be able to design around our patents or develop products that provide outcomes that are comparable to our products but that are not covered by our patents.

We have also entered into confidentiality and assignment of intellectual property agreements with all of our employees, consultants and advisors as one of the ways we seek to protect our intellectual property and other proprietary technology. However, these agreements may not be enforceable or may not provide meaningful protection for our trade secrets or other proprietary information in the event of unauthorized use or disclosure or other breaches of the agreements.

In the event a competitor infringes upon any of our patents or other intellectual property rights, enforcing our rights may be difficult, time consuming and expensive, and would divert management’s attention from managing our business. There can be no assurance that we will be successful on the merits in any enforcement effort. In addition, we may not have sufficient resources to litigate, enforce or defend our intellectual property rights.

We have no patent protection covering the composition of matter for our solid silicon nitride or for all of the components of the process we use for manufacturing our silicon nitride, and competitors may create silicon nitride formulations substantially similar to ours.

Although we have a number of U.S. and foreign patents and pending applications relating to our solid silicon nitride products or product candidates, we have no patent protection either for the composition of matter for our silicon nitride or for the processes of manufacturing solid silicon nitride. As a result, competitors may create silicon nitride formulations substantially similar to ours and use their formulations in products that may compete with our silicon nitride products, provided they do not violate our issued product patents. Although we have, and will continue to develop, significant know-how related to these processes, there can be no assurance that we will be able to maintain this know-how as trade secrets, and competitors may develop or acquire equally valuable or more valuable know-how related to the manufacture of silicon nitride.

We could become subject to intellectual property litigation that could be costly, result in the diversion of management’s time and efforts, require us to pay damages, prevent us from marketing our commercially available products or product candidates and/or reduce the margins we may realize from our products that we may commercialize.

The medical devices industry is characterized by extensive litigation and administrative proceedings over patent and other intellectual property rights. Whether a product infringes a patent involves complex legal and factual issues, and the determination is often uncertain. There may be existing patents of which we are unaware that our products under development may inadvertently infringe. The likelihood that patent infringement claims may be brought against us increases as the number of participants in the orthopedic market increases and as we achieve more visibility in the marketplace and introduce products to market.

Any infringement claim against us, even if without merit, may cause us to incur substantial costs, and would place a significant strain on our financial resources, divert the attention of management from our core business, and harm our reputation. In some cases, litigation may be threatened or brought by a patent holding company or other adverse patent owner who has no relevant product revenues and against whom our patents may provide little or no deterrence. If we were found to infringe any patents, we could be required to pay substantial damages, including triple damages if an infringement is found to be willful, and royalties and could be prevented from selling our products unless we obtain a license or are able to redesign our products to avoid infringement. We may not be able to obtain a license enabling us to sell our products on reasonable terms, or at all, and there can be no assurance that we would be able to redesign our products in a way that would not infringe those patents. If we fail to obtain any required licenses or make any necessary changes to our technologies or the products that incorporate them, we may be unable to commercialize one or more of our products or may have to withdraw products from the market, all of which would have a material adverse effect on our business, financial condition and results of operations.

In addition, in order to further our product development efforts, we have entered into agreements with orthopedic surgeons to help us design and develop new products, and we expect to enter into similar agreements in the future. In certain instances, we have agreed to pay such surgeons royalties on sales of products which incorporate their product development contributions. There can be no assurance that surgeons with whom we have entered into such arrangements will not claim to be entitled to a royalty even if we do not believe that such products were developed by cooperative involvement between us and such surgeons. In addition, some of our surgeon advisors are employed by academic or medical institutions or have agreements with other orthopedic companies pursuant to which they have agreed to assign or are under an obligation to assign to those other companies or institutions their rights in inventions which they conceive or develop or help conceive or develop.

There can be no assurance that one or more of these orthopedic companies or institutions will not claim ownership rights to an invention we develop in collaboration with our surgeon advisors or consultants on the basis that an agreement with such orthopedic company or institution gives it ownership rights in the invention or that our surgeon advisors on consultants otherwise have an obligation to assign such inventions to such company or institution. Any such claim against us, even without merit, may cause us to incur substantial costs, and would place a significant strain on our financial resources, divert the attention of management from our core business and harm our reputation.

We may be subject to damages resulting from claims that we have wrongfully used or disclosed alleged trade secrets of our competitors or are in breach of non-competition agreements with our competitors or non-solicitation agreements.

Some of our employees were previously employed at other medical device or ceramic companies, including our competitors and potential competitors. Many of our former distributors and potential distributors sell, or in the past have sold, products of our competitors. We may be subject to claims that either we, or these employees or distributors, have inadvertently or otherwise used or disclosed the trade secrets or other proprietary information of our competitors. In addition, we have been and may in the future be subject to claims that we caused an employee or sales agent to break the terms of his or her non-competition agreement or non-solicitation agreement. Litigation may be necessary to defend against these claims. Even if we are successful in defending against these claims, litigation could result in substantial costs and be a distraction to management. If we fail in defending such claims, in addition to paying money damages, we may lose valuable intellectual property rights or personnel. A loss of key personnel or their work product could hamper or prevent our ability to commercialize products, which could have an adverse effect on our business, financial condition and results of operations.

If our advanced ceramic products or our product candidates conflict with the rights of others, we may not be able to manufacture or market our products or product candidates, which could have a material and adverse effect on us.

Our commercial success will depend in part on not infringing the patents or violating the other proprietary rights of third parties. Issued patents held by others may limit our ability to develop commercial products. All issued patents are entitled to a presumption of validity under the laws of the United States. If we need suitable licenses to such patents to permit us to develop or market our product candidates, we may be required to pay significant fees or royalties and we cannot be certain that we would even be able to obtain such licenses. Competitors or third parties may obtain patents that may cover subject matter we use in developing the technology required to bring our products to market, that we use in producing our products, or that we use in treating patients with our products. We know that others have filed patent applications in various jurisdictions that relate to several areas in which we are developing products. Some of these patent applications have already resulted in patents and some are still pending. If we were found to infringe any of these issued patents or any of the pending patent applications, when and if issued, we may be required to alter our processes or product candidates, pay licensing fees or cease activities. If use of technology incorporated into or used to produce our product candidates is challenged, or if our processes or product candidates conflict with patent rights of others, third parties could bring legal actions against us, in Europe, the United States and elsewhere, claiming damages and seeking to enjoin manufacturing and marketing of the affected products. Additionally, it is not possible to predict with certainty what patent claims may issue from pending applications. In the United States, for example, patent prosecution can proceed in secret prior to issuance of a patent, provided such application is not filed in foreign jurisdiction. For U.S. patent applications that are also filed in foreign jurisdictions, such patent applications will not publish until 18 months from the filing date of the application. As a result, third parties may be able to obtain patents with claims relating to our product candidates which they could attempt to assert against us. Further, as we develop our products, third parties may assert that we infringe the patents currently held or licensed by them, and we cannot predict the outcome of any such action.

There has been extensive litigation in the medical devices industry over patents and other proprietary rights. If we become involved in any litigation, it could consume a substantial portion of our resources, regardless of the outcome of the litigation. If these legal actions are successful, in addition to any potential liability for damages, we could be required to obtain a license, grant cross-licenses and pay substantial royalties in order to continue to manufacture or market the affected products.

We cannot assure you that we would prevail in any legal action or that any license required under a third-party patent would be made available on acceptable terms, or at all. Ultimately, we could be prevented from commercializing a product, or forced to cease some aspect of our business operations, as a result of claims of patent infringement or violation of other intellectual property rights, which could have a material and adverse effect on our business, financial condition and results of operations.

Risks Related to Potential Litigation from Operating Our Business

We may become subject to potential product liability claims, and we may be required to pay damages that exceed our insurance coverage.

Our business exposes us to potential product liability claims that are inherent in the design, testing, manufacture, sale and distribution of our currently marketed products and each of our product candidates that we are seeking to introduce to the market. The use of orthopedic medical devices can involve significant risks of serious complications, including bleeding, nerve injury, paralysis, infection, and even death. Any product liability claim brought against us, with or without merit, could result in the increase of our product liability insurance rates or in our inability to secure coverage in the future on commercially reasonable terms, if at all. In addition, if our product liability insurance proves to be inadequate to pay a damage award, we may have to pay the excess of this award out of our cash reserves, which could significantly harm our financial condition. If longer-term patient results and experience indicate that our products or any component of a product causes tissue damage, motor impairment or other adverse effects, we could be subject to significant liability. A product liability claim, even one without merit, could harm our reputation in the industry, lead to significant legal fees, and result in the diversion of management’s attention from managing our business.

Any claims relating to our improper handling, storage or disposal of biological or hazardous materials could be time consuming and costly.

Although we do not believe that the manufacture of our silicon nitride or non-silicon nitride products will involve the use of hazardous materials, it is possible that regulatory authorities may disagree or that changes to our manufacturing processes may result in such use. Our business and facilities and those of our suppliers and future suppliers may therefore be subject to foreign, federal, state and local laws and regulations governing the use, manufacture, storage, handling and disposal of hazardous materials and waste products. We may incur significant expenses in the future relating to any failure to comply with environmental laws. Any such future expenses or liability could have a significant negative impact on our business, financial condition and results of operations.

Risks Related to Public Companies

We are a “smaller reporting company” and the reduced disclosure requirements applicable to smaller reporting companies may make our common stock less attractive to investors.

We are currently a “smaller reporting company” as defined in the Securities Exchange Act of 1934. Smaller reporting companies are able to provide simplified executive compensation disclosures in their filings, are exempt from the provisions of Section 404(b) of the Sarbanes-Oxley Act requiring that independent registered public accounting firms provide an attestation report on the effectiveness of internal control over financial reporting, and have certain other decreased disclosure obligations in their SEC filings, including, among other things, only being required to provide two years of audited financial statements in annual reports. We cannot predict whether investors will find our common stock less attractive because of our reliance on any of these exemptions. If some investors find our common stock less attractive as a result, there may be a less active trading market for our common stock and our stock price may be more volatile.

We incur substantial costs as a result of being a public company and our management expects to devote substantial time to public company compliance programs.

As a public company, we incur significant legal, insurance, accounting and other expenses, including costs associated with public company reporting. We intend to invest resources to comply with evolving laws, regulations and standards, and this investment will result in increased general and administrative expenses and may divert management’s time and attention from product development and commercialization activities. If our efforts to comply with new laws, regulations and standards differ from the activities intended by regulatory or governing bodies due to ambiguities related to practice, regulatory authorities may initiate legal proceedings against us, and our business may be harmed. These laws and regulations could make it more difficult and costlier for us to obtain director and officer liability insurance for our directors and officers, and we may be required to accept reduced coverage or incur substantially higher costs to obtain coverage. These factors could also make it more difficult for us to attract and retain qualified executive officers and qualified members of our board of directors, particularly to serve on our audit and compensation committees. In addition, if we are unable to continue to meet the legal, regulatory and other requirements related to being a public company, we may not be able to maintain the listing of our common stock on The NASDAQ Capital Market, which would likely have a material adverse effect on the trading price of our common stock.

We may not be able to maintain our listing on the NASDAQ Capital Market, which would adversely affect the price and liquidity of our common stock.

As a small capitalization company, the price of our common shares has been, and is likely to continue to be, highly volatile. Any announcements concerning us or our competitors, quarterly variations in operating results, introduction of new products, delays in the introduction of new products or changes in product pricing policies by us or our competitors, acquisition or loss of significant customers, partners and suppliers, changes in earnings estimates or our ratings by analysts, regulatory developments, or fluctuations in the economy or general market conditions, among other factors, could cause the market price of our common shares to fluctuate substantially. There can be no assurance that the market price of our common shares will not decline below its current price or that it will not experience significant fluctuations in the future, including fluctuations that are unrelated to our performance.

Currently our common stock is quoted on the NASDAQ Capital Market under the symbol “SINT”. We must satisfy certain minimum listing maintenance requirements to maintain the NASDAQ Capital Market quotation, including certain governance requirements and a series of financial tests relating to stockholders’ equity or net income or market value, public float, number of market makers and stockholder, market capitalization, and maintaining a minimum bid price of $1.00 per share.

On October 20, 2023, we received a notice from the Listing Qualifications Department of The NASDAQ Stock Market stating that the bid price of our common stock for the previous 30 consecutive trading days had closed below the minimum $1.00 per share required for continued listing on The NASDAQ Capital Market under NASDAQ Listing Rule 5550(a)(2). We had a period of 180 calendar days, or until April 17, 2024, to regain compliance with the rule.

If the Company does not regain compliance with Rule 5550(a)(2) by April 17, 2024, the Company may be eligible for additional time. To qualify, the Company will be required to meet the continued listing requirement for market value of publicly held shares and all other initial listing standards for The Nasdaq Capital Market, with the exception of the bid price requirement, and will need to provide written notice of its intention to cure the deficiency during the second compliance period, by effecting a reverse stock split, if necessary. If the Company meets these requirements, the Staff will inform the Company that it has been granted an additional 180 calendar days. However, if it appears to Staff that the Company will not be able to cure the deficiency, or if the Company is otherwise not eligible, the Staff will provide notice that its securities will be subject to delisting. We intend to actively monitor our bid price and will consider available options to resolve the deficiency and regain compliance with the Nasdaq Listing Rules, including considering whether to conduct a reverse stock split.

If Nasdaq delists our common stock from trading on its exchange and we are not able to list our securities on another national securities exchange, we expect our securities could be quoted on an over-the-counter market. If this were to occur, we could face significant material adverse consequences, including:

Not applicable.

Risk Management and Strategy

We regularly assess risks from cybersecurity threats, monitor our information systems for potential vulnerabilities, and test those systems pursuant to our cybersecurity policies, processes, and practices, which are integrated into our overall risk management program. To protect our information systems from cybersecurity threats, we use various security tools that are designed to help identify, escalate, investigate, resolve, and recover from security incidents in a timely manner. Our board of directors assesses risks based on probability and potential impact to key business systems and processes as part of our overall risk management program overseen by the board of directors. Risks that are considered high are incorporated into our overall risk management program. We collaborate with third parties to assess the effectiveness of our cybersecurity prevention and response systems and processes and to assist in the identification, verification, and validation of cybersecurity risks, as well as to support associated mitigation plans when necessary. We have also developed a third-party cybersecurity risk management process to conduct due diligence on external entities, including those that perform cybersecurity services. Cybersecurity threats, including those resulting from any previous cybersecurity incidents, have not materially affected our Company, including our business strategy, results of operations, or financial condition. Refer to the risk factor captioned “Cyber security risks and the failure to maintain the integrity of company, employee or guest data could expose us to data loss, litigation and liability, and our reputation could be significantly harmed.” in Part I, Item 1A. “Risk Factors” for additional details regarding cybersecurity risks and potential impacts on our business.

Governance

Our board of directors oversees our risk management process, including as it pertains to cybersecurity risks, which focuses on the most significant risks we face in the short-, intermediate-, and long-term timeframe. Management is responsible for the operational oversight of company-wide cybersecurity strategy, policy, and standards across relevant departments to assess and help prepare us to address cybersecurity risks. Meetings of our board of directors include discussions and presentations from management regarding specific risk areas throughout the year, including, among others, those relating to cybersecurity threats, and reports from management on our enterprise risk profile on an annual basis. The board of directors reviews our cybersecurity risk profile with management on a periodic basis using key performance and/or risk indicators. These key performance indicators are metrics and measurements designed to assess the effectiveness of our cybersecurity program in the prevention, detection, mitigation, and remediation of cybersecurity incidents. We take a risk-based approach to cybersecurity and have implemented cybersecurity policies throughout our operations that are designed to address cybersecurity threats and incidents.

Our 30,764 square foot corporate office and manufacturing facilities are located in Salt Lake City, Utah. We occupy these facilities pursuant to a lease that expires in December 2024. Pursuant to the terms of the lease agreement, we may extend the lease for two additional periods of five years each.

We also lease a 10,936 square foot facility located in Salt Lake City, Utah. This facility houses our Armor business. We occupy this facility pursuant to a lease that expires in October 2031.

In connection with operation of Maryland based subsidiary Technology Assessments and Transfer, Inc., we have entered into various leases from which we conduct research, development and manufacturing activities. The leases have various expiration dates ranging from July 2023 through April 2025.

We believe that our existing facilities are adequate for our current and projected needs for the foreseeable future.

We are currently not a party to any material legal proceedings. However, our industry is characterized by frequent claims and litigation, including claims regarding intellectual property and product liability. As a result, we may be subject to various legal proceedings in the future.

This item does not apply to our business.

PART II

Market Information

Our shares of common stock are currently quoted on The NASDAQ Capital Market under the symbol “SINT”.

Holders of Record

As of December 31, 2023, we had approximately 159 holders of record of our common stock. Because many of our shares of common stock are held by brokers and other institutions on behalf of stockholders, this number is not indicative of the total number of stockholders represented by these stockholders of record.

Dividends

We have not declared or paid dividends to stockholders since inception and do not plan to pay cash dividends in the foreseeable future. We currently intend to retain earnings, if any, to finance our growth.

Issuer Purchases of Equity Securities

None

You should read the following discussion and analysis of our financial condition and results of operations together with our consolidated financial statements and related notes appearing elsewhere in this Annual Report. This discussion and analysis contain forward-looking statements based upon current beliefs, plans, expectations, intentions and projections that involve risks, uncertainties and assumptions, such as statements regarding our plans, objectives, expectations, intentions and projections. Our actual results and the timing of selected events could differ materially from those anticipated in these forward-looking statements as a result of several factors, including those set forth under “Risk Factors” and elsewhere in this Annual Report.

Overview

SINTX Technologies is an advanced ceramics company formed in December 1996, focused on providing solutions in a variety of biomedical, technical, and antipathogenic applications. We have grown from focusing primarily on the research, development and commercialization of medical devices manufactured with silicon nitride to becoming an advanced ceramics company engaged in diverse fields, including biomedical, technical and antipathogenic applications. This diversification enables us to focus on our core competencies which are the manufacturing, research, and development of products comprised from advanced ceramic materials for external partners. We seek to connect with new customers, partners and manufacturers to help them realize the goal of leveraging our expertise in advanced ceramics to create new, innovative products across these sectors.

SINTX Core Business

Biomedical Applications: Since its inception, SINTX has been focused on medical grade silicon nitride. SINTX biomedical products have been shown to be biocompatible, bioactive, antipathogenic, and to have superb bone affinity. Spinal implants made from SINTX silicon nitride have been successfully implanted in humans since 2008 in the US, Europe, Brazil, and Taiwan. This established use, along with its inherent resistance to bacterial adhesion and bone affinity suggests that it may also be suitable in other fusion device applications such as arthroplasty implants, foot wedges, and dental implants. Bacterial infection of any biomaterial implants is always a concern. SINTX silicon nitride has been shown to be resistant to bacterial colonization and biofilm formation, making it antibacterial. SINTX silicon nitride products can be polished to a smooth and wear-resistant surface for articulating applications, such as bearings for hip and knee replacements.

We believe that silicon nitride has a superb combination of properties that make it suited for long-term human implantation. Other biomaterials are based on bone grafts, metal alloys, and polymers- all of which have well-known practical limitations and disadvantages. In contrast, silicon nitride has a legacy of success in the most demanding and extreme industrial environments. As a human implant material, silicon nitride offers bone ingrowth, resistance to bacterial and viral infection, ease of diagnostic imaging, resistance to corrosion, and superior strength and fracture resistance, all of which claims are validated in our large and growing inventory of peer-reviewed, published literature reports. We believe that our versatile silicon nitride manufacturing expertise positions us favorably to introduce new and innovative devices in the medical and non-medical fields.

In June 2022, we acquired Technology Assessment and Transfer, Inc. (TA&T), a nearly 40-year-old business with a mission to transition advanced materials and process technologies from a laboratory environment to commercial products and services. TA&T has supplied ceramics for use in several biomedical applications. These products were made via 3D printing and include components for surgical instruments as well as conceptual and prototype dental implants.

Technical Applications: It is our belief that our silicon nitride has the best combination of mechanical, thermal, and electrical properties of any technical ceramic material. It is a high-performance technical ceramic with high strength, toughness, and hardness, and is extremely resistant to thermal shock and impact. It is also an electrically insulating ceramic material. Typically, it is used in applications where high load-bearing capacity, thermal stability, and wear resistance are required. We have obtained AS9100D certification and ITAR registration to facilitate entry into the aerospace and protective armor markets.

We entered the ceramic armor market through the purchase of assets from B4C, LLC and a technology partnership with Precision Ceramics USA. We will develop and manufacture high-performance ceramics for personnel, aircraft, and vehicle armor including a 100% Boron Carbide material for ultimate lightweight performance in ballistic applications, and a composite material made of Boron Carbide and Silicon Carbide for exceptional multi-hit performance against ballistic threats. We have signed a 10-year lease at a building near our headquarters in Salt Lake City, Utah to house development and manufacturing activities for SINTX Armor.

TA&T’s primary area of expertise is material processing and fabrication know-how for a broad spectrum of monolithic ceramic, ceramic composite, and coating materials. Primary technologies include Additive Manufacturing (3D Printing) of ceramics and metals, low-cost fabrication of fiber reinforced ceramic matrix composites (CMCs) and refractory chemical vapor deposited (CVD) coatings, transparent ceramics for ballistic armor and optical applications, and magnetron sputtered (PVD) coatings for lubrication, wear resistance and environmental barrier coatings for CMCs. TA&T also provides a host of services that include 3D printing, PVD-CVD coatings, material processing-CMCs, CIP, PS, HP, HIP, and material characterization for powders and finished parts-TGA/DSC, PSD. SA, Dilatometry, UV-VIS and FTIR transmission, haze and clarity.

Antipathogenic Applications: Today, there is a global need to improve protection against pathogens in everyday life. SINTX believes that by incorporating its unique composition of silicon nitride antipathogenic powder into products such as face masks, filters, and wound care devices, it is possible to manufacture surfaces that inactivate pathogens, thereby limiting the spread of infection and disease. The discovery in 2020 that SINTX silicon nitride inactivates SARS-CoV-2, the virus which causes the disease COVID-19, has opened new markets and applications for our material.

We presently manufacture advanced ceramic powders and components in our manufacturing facilities based in Salt Lake City, Utah and Millersville, Maryland.

Components of our Results of Operations

We manage our business within one reportable segment, which is consistent with how our management reviews our business, makes investment and resource allocation decisions and assesses operating performance.

Revenue

Our product revenue is derived from the manufacture and sale of products. These revenue sources include coatings, components for aerospace and medical device markets, toll processing services, and government contracts and grants. We generally recognize revenue from sales where control transfers at a point in time as the title and risk of loss passes to the customer, which is at the time the product is shipped. In general, our customer does not have rights of return or exchange.

We believe our product revenue will increase as we secure opportunities to manufacture third party products with silicon nitride, launch and generate revenue from our ceramic armor products, and as we continue to introduce new products into the market.

We derive grant and contract revenue from awards provided by governmental agencies.

Cost of Revenue

The expenses that are included in cost of revenue include all in-house manufacturing costs for the products we manufacture.

Gross Profit

Our gross profit measures our product revenue relative to our cost of revenue.

Research and Development Expenses

Our research and development costs are expensed as incurred. Research and development costs consist of engineering, product development, clinical trials, test-part manufacturing, testing, developing and validating the manufacturing process, manufacturing, facility and regulatory-related costs. Research and development expenses also include employee compensation, employee and non-employee stock-based compensation, supplies and materials, consultant services, and travel and facilities expenses related to research and development activities.

We expect to incur additional research and development costs as we continue to develop new medical devices, industrial and ceramic armor products, product candidates for antipathogenic applications, and other products which may increase our total research and development expenses.

General and Administrative Expenses

General and administrative expenses consist primarily of salaries, benefits and other related costs, including stock-based compensation for certain members of our executive team and other personnel employed in finance, compliance, administrative, information technology, customer service, executive and human resource departments. General and administrative expenses also include other expenses not part of the other cost categories mentioned above, including facility expenses and professional fees for accounting and legal services.

Results of Operations

Year Ended December 31, 2023 Compared to the Year Ended December 31, 2022

The following table sets forth, for the periods indicated, our results of operations for the years ended December 31, 2023 and 2022 (dollars, in thousands):

Product Revenue

Total product revenue increased $0.6 million, or 104%, as compared to the same period in 2022. During the year ended December 31, 2023, the Company grant and contract revenue increased $0.4 million as compared to the same period in 2022.

Costs of Revenue and Gross Profit

Cost of revenue increased $0.5 million, or 196% as compared to the same period in 2022. This increase was primarily attributable to an increase in product revenue and a shift in customer base and product mix. Gross profit increased $0.5 million, or 42%, as compared to the same period in 2022. This increase was primarily attributed to an increase in grant and contract revenue and a shift in product mix to more profitable products.

Research and Development Expenses

Research and development expenses increased $2.3 million, or 35%, as compared to the same period in 2022. This increase was primarily attributable to an increase in patent expenses, employee wages, product prototypes, and costs of operations associated with opening the SINTX Armor facility and the acquisition of TA&T.

General and Administrative Expenses

General and administrative expenses increased $0.2 million, or 6%, as compared to the same period in 2022. This increase is primarily due to an increase in costs for investor relations, employee wages, and employee recruitment costs.

Sales and Marketing Expenses

Sales and marketing expenses decreased $0.2 million, or -15%, as compared to the same period in 2022. This decrease was primarily attributable to a reduction in employee wages and an overall decrease in costs for outside consulting.

Grant and Contract Expenses

Grant and contract expenses increased $0.2 million, or 32%, as compared to the same period in 2022. This increase was primarily attributable to a general increase in grant and contract revenue when compared to the prior year.

Other Income (Expense), Net

Other income (expenses) increased $5.8 million, or 824%, as compared to the same period in 2022. This increase was primarily due to the change in the fair value of the derivative liabilities in the amount of $6.8 million, and a $0.1 million increase in other income offset by a $0.8 million in offering costs on derivative liabilities and a $0.3 million decrease in other income.

Liquidity and Capital Resources

The consolidated financial statements have been prepared assuming the Company will continue to operate as a going concern, which contemplates the realization of assets and settlement of liabilities in the normal course of business, and does not include any adjustments to reflect the possible future effects on the recoverability and classification of assets or the amounts and classifications of liabilities that may result from uncertainty related to its ability to continue as a going concern within one year from the date of issuance of these consolidated financial statements.

For the years ended December 31, 2023 and 2022, the Company incurred a net loss of $8.3 million and $12.0 million, respectively, and used cash in operations of $14.1 million and $10.3 million, respectively. The Company had an accumulated deficit of $270.7 million and $262.5 million as of December 31, 2023 and 2022, respectively.

The Company’s operations have been principally financed from proceeds from the issuance of preferred and common stock and, to a lesser extent, cash generated from product sales. It is anticipated that the Company will continue to generate operating losses and use cash in operations. The Company’s continuation as a going concern is dependent upon its ability to increase sales, and/or raise additional funds through the capital markets. Whether and when the Company can attain profitability and positive cash flows from operations or obtain additional financing is uncertain.

The Company is actively generating additional scientific and clinical data to have it published in leading industry publications. We believe the publication of such data would help sales efforts as the Company approaches new prospects. The Company is also making additional changes to the sales strategy, including a focus on revenue growth by expanding the use of silicon nitride in other areas outside of spinal fusion applications. For instance, results from an independent study demonstrated the potential anti-viral properties of our silicon nitride. We believe that we may be able to apply our silicon nitride powder to personal protection products, such as face masks, gowns and gloves, resulting in inactivation of viruses that come into contact with the items.

The Company has common stock that is publicly traded and has been able to successfully raise capital when needed since the date of the Company’s initial public offering in February 2014.

On February 2, 2024, the Company closed on a public offering of 16,000,000 units, with each unit consisting of one share of its common stock, or one pre-funded warrant to purchase one share of its common stock, one Class E Warrant with each warrant to purchase one share of common stock, and one Class F Warrant with each warrant to purchase one share of common stock. Each unit was sold at a public offering price of $0.25. The Class E and Class F Warrants in the units are immediately exercisable at a price of $0.25 per share. The Class E Warrants will expire five years from the date of issuance and the Class F Warrants will expire eighteen months from the date of issuance. Gross proceeds, before deducting placement agent fees and other offering expenses, are approximately $4.0 million.

On February 10, 2023, the Company closed on a public offering of 2,150,000 units, with each unit consisting of one share of common stock, or one pre-funded warrant to purchase one share of its common stock, one Class C Warrant to purchase one share of common stock, and one half of one Class D Warrant with each whole Class D Warrant entitling the holder to purchase one share of common stock. Gross proceeds, before deducting offering expenses, totaled approximately $12.0 million. Of the $12.0 million of gross proceeds, approximately $5.4 million were allocated to common stock and prefunded warrants ($4.8 million net of offering costs) and approximately $6.7 million were allocated to derivative liabilities (with approximately $0.7 million of cash offering costs and $0.1 million of agent warrant offering costs recorded as derivative expense).

On October 17, 2022, the Company completed a rights offering of units consisting of convertible preferred stock and common stock warrants, resulting in gross proceeds to the Company of approximately $4.7 million, after deducting expenses relating to the offering, including dealer-manager fees and expenses,

On February 25, 2021, the Company entered into an Equity Distribution Agreement with Maxim Group LLC (“Maxim”), which was subsequently amended on October 12, 2023 (as amended, the “2021 Distribution Agreement”), pursuant to which the Company may sell from time to time, shares of the Company’s common stock having an aggregate offering price of up to $1.1 million through Maxim, as agent. Subject to the terms and conditions of the 2021 Distribution Agreement, as amended, Maxim will use its commercially reasonable efforts to sell the shares from time to time, based on our instructions. Under the 2021 Distribution Agreement, Maxim may sell the Shares by any method permitted by law deemed to be an “at-the-market” offering (the “ATM”) as defined in Rule 415 promulgated under the Securities Act of 1933, as amended (the “Securities Act”), including, without limitation, sales made directly on the Nasdaq Capital Market. We have no obligation to sell any shares under the ATM and may at any time suspend offers under the 2021 Distribution Agreement. The Offering will terminate upon the earlier of (i) the sale of shares having an aggregate offering price of $15.0 million, (ii) the termination by either Maxim or the Company upon the provision of fifteen (15) days written notice, or (iii) February 25, 2025. Under the terms of the 2021 Distribution Agreement, Maxim will be entitled to a transaction fee at a fixed rate of 2.0% of the gross sales price of Shares sold under the 2021 Distribution Agreement. The Company will also reimburse Maxim for certain expenses incurred in connection with the 2021 Distribution Agreement and agreed to provide indemnification and contribution to Maxim with respect to certain liabilities under the Securities Act and the Securities Exchange Act of 1934, as amended. As of March 1, 2024, there have been 1,317,749 shares of common stock sold under the 2021 Distribution Agreement for gross proceeds of $0.5 million. Subsequent to December 31, 2023 there have been 1,154,200 shares of common stock sold under the 2021 Distribution for gross proceeds of $0.5 million. In connection with the February 2024 offering, the Company agreed to not make any sales of securities under the ATM for a period of six months from the date of closing the offering, February 2, 2024, until August 2, 2024.

These uncertainties raise substantial doubt about our ability to continue as a going concern. The consolidated financial statements do not include any adjustments that might result from the outcome of these uncertainties.

Cash Flows

The following table summarizes, for the periods indicated, cash flows from operating, investing and financing activities (in thousands):

Net Cash Used in Operating Activities

Net cash used in operating activities was $14.1 million in 2023, compared to $10.3 million used in 2022, an increase of $3.8 million. The increase in the net loss from operations, and related non-cash add backs to the net loss, was $2.3 million from 2023 when compared to 2022. The increase in cash used for operating activities during 2023 was primarily due to the $2.3 million mentioned above plus changes in the movement of working capital items during 2023 as compared to the same period in 2022 as follows: a $0.4 million increase in cash used in accounts receivable, a $0.3 million increase for inventory, a $0.3 million increase in cash used for prepaids, a $0.2 million increase in cash used in other liabilities, a $0.2 million increase in cash used in accounts payable and accrued liabilities, and a $0.1 million increase in cash used for payments on operating lease liability.

Net Cash Used in Investing Activities

Net cash used in investing activities was $0.5 million during 2023, compared to $1.1 million used in investing activities during the same period in 2022, a decrease of $0.6 million. The decrease in cash used in investing activities during 2023 was primarily due to a $0.9 million purchase of property and equipment, offset by and a $0.3 million increase in cash acquired in acquisition in the prior year.

Net Cash Provided by Financing Activities

Net cash provided by financing activities was $11.7 million during 2023, compared to $3.3 million provided by financing activities during the same period in 2022, an increase of $8.4 million. This increase was primarily attributable to an increase in proceeds from issuance of common stock of $5.1 million, an increase in proceeds from issuance of warrant derivative liabilities of $2.8 million, and a $0.5 million decrease in the payment on debt.

Indebtedness

Business Loan

On July 20, 2021, TA&T, entered into a Loan Authorization and Agreement in the amount of approximately $350,000 (the “Business Loan”). The Company made a one-time $35,000 buy down payment when acquiring the loan. The Business Loan bore interest at a rate of 3.75% per annum. The Business Loan was secured by a general security interest in all of the assets of TA&T. The Business Loan contained other standard provisions that are customary of loans of this type. The business loan was paid in full during the first quarter of 2023 and there was no outstanding balance at December 31, 2023.

Related Party Debt

TA&T is obligated to repay certain personal loans made by the founders of TA&T to TA&T prior to SINTX’s acquisition of TA&T (the “Personal Loans”). The total amount of the Personal Loans at September 30, 2022 was approximately $350,000. The Company agreed to repay the outstanding balance of the Personal Loans in (i) 24 equal monthly installments beginning September 1, 2022 and each month thereafter until paid in full as one prior owner’s portion of the Personal Loans totaling $157,000, and (ii) for the other owner’s portion of the Personal Loans totaling $193,000. As of December 31, 2023, the related party debt had an outstanding balance of $46,000. The outstanding balance is being paid in monthly installments ending August 1, 2024. The related party debt is not collateralized and has no interest rate.

Wells Fargo Line of Credit

Prior to SINTX’s acquisition of TA&T, TA&T entered into a revolving line of credit with Wells Fargo. As of December 31, 2023, the line of credit with Wells Fargo had no outstanding balance and the account has been closed.

Off-Balance Sheet Arrangements

We do not have any off-balance sheet arrangements, as defined in Item 303(a)(4) of Regulation S-K.

Related-Party Transactions

We have not entered into any transactions since January 1, 2021 to which we have been a party, in which the amount involved in the transaction exceeded the lesser of $120,000 or one percent of the average of our total assets at year-end for the last two completed fiscal years, and in which any of our directors, executive officers or, to our knowledge, beneficial owners of more than 5% of our common stock, on an as converted basis, or any member of the immediate family of any of the foregoing persons had or will have a direct or indirect material interest, other than equity and other compensation, termination, change in control and other arrangements.

Indemnification Agreements: We have entered into indemnification agreements with each of our executive officers and directors that require us to indemnify such persons against any and all expenses, including judgments, fines or penalties, attorney’s fees, witness fees or other professional fees and related disbursements and other out-of-pocket costs incurred, in connection with any action, suit, arbitration, alternative dispute resolution mechanism, investigation, inquiry or administrative hearing, whether threatened, pending or completed, to which any such person may be made a party by reason of the fact that such person is or was a director, officer, employee or agent of our company, provided that such director or officer acted in good faith and in a manner that the director or officer reasonably believed to be in, or not opposed to, our best interests. The indemnification agreements also set forth procedures that will apply in the event of a claim for indemnification thereunder. We believe that these provisions and agreements are necessary to attract and retain qualified persons as directors and officers.

Seasonality and Backlog

Our business is generally not seasonal in nature. The majority of our product revenue is derived from the manufacture and sale of spinal fusion products, used in the treatment of spine disorders, to CTL Medical. We also retained CTL Medical to act as our exclusive broker to offer for sale, and sell, our manufacturing services to third party developers of spinal implants and spinal devices that incorporate silicon nitride technology, which has a remaining term of 5-years. CTL Medical’s sales generally consist of products that are in stock with them or maintained at hospitals or with their sales distributors. Accordingly, we do not have a backlog of sales orders.

Critical Accounting Policies and Estimates

A summary of our significant accounting policies and estimates is discussed in Management’s Discussion and Analysis of Financial Condition and Results of Operations and in Note 1 to our consolidated financial statements included in our Annual Report on Form 10-K for the year ended December 31, 2023. There have been no material changes to those policies for the year ended December 31, 2023. The preparation of the consolidated financial statements in accordance with U.S. generally accepted accounting principles requires us to make judgments, estimates and assumptions regarding uncertainties that affect the reported amounts of assets and liabilities. Significant areas of uncertainty that require judgments, estimates and assumptions include the accounting for income taxes and other contingencies as well as valuation of derivative liabilities, asset impairment and collectability of accounts receivable. We use historical and other information that we consider to be relevant to make these judgments and estimates. However, actual results may differ from those estimates and assumptions that are used to prepare our consolidated financial statements.

New Accounting Pronouncement, Not Yet Adopted

The Company has reviewed all recently issued, but not yet adopted, accounting standards, in order to determine their effects, if any, on its results of operations, financial position or cash flows. Based on that review, the Company believes that no other pronouncements will have a significant effect on its financial statements upon adoption.

Revenue Recognition

The Company derives its product revenue primarily from the sale of aerospace components and spinal fusion products, used in the treatment of spine disorders to CTL Medical, with whom the Company has a 10-year exclusive sales agreement in place, 7 years of which remain. The Company is currently pursuing other sales opportunities for silicon nitride outside the spinal fusion application. The sale of the Company’s products has a single performance obligation and revenue is recognized at the time the product is shipped to the customer. In general, the Company’s customers do not have any rights of return or exchange.

Revenue is recognized when control of the goods or services promised under the contract is transferred to the customer either at a point in time (e.g., upon delivery) or over time (e.g., as performed under the contract). The Company accounts for a contract when it has approval and commitment from both parties, the rights and payment terms of the parties are identified, the contract has commercial substance and collectability of consideration is probable. Contracts are reviewed to determine whether there is one or multiple performance obligations. A performance obligation is a promise to transfer a distinct good or service to a customer and represents the unit of accounting for revenue recognition. For contracts with multiple performance obligations, the expected consideration, or the transaction price, is allocated to each performance obligation identified in the contract based on the relative standalone selling price of each performance obligation. Revenue is then recognized for the transaction price allocated to the performance obligation when control of the promised goods or services underlying the performance obligation is transferred. Contract consideration is not adjusted for the effects of a significant financing component when, at contract inception, the period between when control transfers and when the customer will pay for that good or service is one year or less. Contact modifications that provide for additional distinct goods or services at the standalone selling price are treated as separate contracts. The transaction price for our contracts reflects our estimate of returns, rebates and discounts, which historically have not been significant. Amounts billed to customers for shipping and handling are included in the transaction price and generally are not treated as separate performance obligations as these costs fulfill a promise to transfer the product to the customer. The Company does not employee salespeople to actively seek additional customers; there are no incremental costs for obtaining customers that need to be capitalized.

Account and Other Receivables and Allowance for Credit Losses Doubtful Accounts

Financial assets, which potentially subject the Company to credit losses, consist primarily of receivables. We measure expected credit losses of financial assets based on historical loss and other information available to management using type of receivable (commercial, grants or contracts, retainage, or other) and different aging categories (less than 90 days past due, over 90 days past due, over 180 days past due, and financially troubled customers). These expected credit losses are recorded to an allowance for credit losses valuation account that is deducted from receivables to present the net amount expected to be collected on the financial asset on the consolidated balance sheet. Management believes that the historical loss information it has compiled is a reasonable basis on which to determine expected credit losses for trade receivables held as of December 31, 2023, because the composition of the trade receivables as of that date is consistent with that used in developing the historical credit-loss percentages (i.e., the similar risk characteristics of its customers and its lending practices have not changed significantly over time).

Inventories

Inventories are stated at the lower of cost or net realizable value, with cost for manufactured inventory determined under the standard costs, which approximate actual costs, determined on the first-in first-out (“FIFO”) method. Manufactured inventory consists of raw material, direct labor and manufacturing overhead cost components. The Company reviews the carrying value of inventory on a periodic basis for excess or obsolete items, and records any write-down as a cost of revenue, as necessary.

Long Lived Intangible Assets

The Company evaluates the carrying value of intangibles when events or changes in circumstances indicate that the carrying value may not be recoverable. Factors the Company considers important which could trigger an impairment review include, but are not limited to, significant under-performance relative to historical or projected future operating results, significant changes in the manner of its use of acquired assets or its overall business strategy, and significant industry or economic trends. The Company amortizes definite-lived intangible assets on a straight-line basis over their useful lives. The Company recorded no impairment loss for definite-lived intangible assets during the year ended December 31, 2023. As explained above, the Company sold most intangible assets that had a carrying value, retaining the carrying value of only one trademark asset.

Property and Equipment

Property and equipment, including leasehold improvements, are stated at cost, less accumulated depreciation and amortization. Property and equipment are depreciated using the straight-line method over the estimated useful lives of the assets, which range from three to five years. Leasehold improvements are amortized over the shorter of their estimated useful lives or the related lease term, generally five years.

The Company reviews the carrying value of the Company’s property and equipment that are held and used in the Company’s operations for impairment whenever events or changes in circumstances indicate that the carrying amount of an asset may not be recoverable. Recoverability of these assets is determined based upon expected undiscounted future net cash flows from the operations to which the assets relate, utilizing management’s best estimate, assumptions, and projections at the time. If the carrying value is determined to be unrecoverable from future operating cash flows, the asset is deemed impaired and an impairment charge would be recognized to the extent the carrying value exceeded the estimated fair value of the asset. The Company estimates the fair value of assets based on the estimated future discounted cash flows of the asset.

Income Taxes

The Company recognizes deferred tax assets and liabilities for the future tax consequences attributable to the differences between the financial statement carrying value of existing assets and liabilities and their respective tax bases. Deferred tax assets and liabilities are measured using enacted tax rates in effect for the fiscal year in which those temporary differences are expected to be recovered or settled. Valuation allowances are established when necessary to reduce deferred tax assets to the amount expected to be realized.

The Company operates in various tax jurisdictions and is subject to audit by various tax authorities. The Company provides for tax contingencies whenever it is deemed probable that a tax asset has been impaired, or a tax liability has been incurred for events such as tax claims or changes in tax laws. Tax contingencies are based upon their technical merits relative tax law and the specific facts and circumstances as of each reporting period. Changes in facts and circumstances could result in material changes to the amounts recorded for such tax contingencies.

The Company recognizes uncertain income tax positions taken on income tax returns at the largest amount that is more-likely than-not to be sustained upon audit by the relevant taxing authority. An uncertain income tax position will not be recognized if it has less than a 50% likelihood of being sustained.

The Company’s policy for recording interest and penalties associated with uncertain tax positions is to record such items as a component of our income tax provision. For the years ended December 31, 2023 and 2022, the Company did not record any material interest income, interest expense or penalties related to uncertain tax positions or the settlement of audits for prior periods.

Stock-Based Compensation

The Company measures stock-based compensation expense related to employee stock-based awards based on the estimated fair value of the awards as determined on the date of grant and is recognized as expense over the remaining requisite service period. The Company utilizes the Black-Scholes-Merton option pricing model to estimate the fair value of employee stock options. The Black-Scholes-Merton model requires the input of highly subjective and complex assumptions, including the estimated fair value of the Company’s common stock on the date of grant, the expected term of the stock option, and the expected volatility of the Company’s common stock over the period equal to the expected term of the grant. The Company estimates forfeitures at the date of grant and revises the estimates, if necessary, in subsequent periods if actual forfeitures differ from those estimates. The Company accounts for stock options to purchase shares of stock that are issued to non-employees based on the estimated fair value of such instruments using the Black-Scholes-Merton option pricing model.

Derivative Liabilities

Derivative liabilities include the fair value of instruments such as common stock warrants, preferred stock warrants and convertible features of notes, that are initially recorded at fair value and are required to be re-measured to fair value at each reporting period. The change in fair value of the instruments is recognized as a component of other income (expense) in the Company’s consolidated statements of operations until the instruments settle, expire or are no longer classified as derivative liabilities. The Company estimates the fair value of these instruments using the Black-Scholes-Merton or Monte-Carlo valuation models depending on the complexity of the underlying instrument. The significant assumptions used in estimating the fair value include the exercise price, volatility of the stock underlying the instrument, risk-free interest rate, estimated fair value of the stock underlying the instrument and the estimated life of the instrument.

Not applicable.

Financial Statements

The consolidated financial statements of the Company appear at the end of this Annual Report beginning with the index to Financial Statements on page F-1 (see Part IV, Item 15 “Financial Statements”), and are incorporated herein.

None.

(a) Disclosure Controls and Procedures

We maintain disclosure controls and procedures, as such term is defined in Rules 13a-15(e) and 15d-15(e) of the Securities Exchange Act of 1934 (the “Exchange Act”), that are designed to ensure that information required to be disclosed in the reports filed or submitted under the Exchange Act, is recorded, processed, summarized, and reported within the time periods specified by the Commission’s rules and forms. Disclosure controls and procedures include controls and procedures designed to ensure that information required to be disclosed in our reports filed or submitted under the Exchange Act are properly recorded, processed, summarized and reported within the time periods required by the Commission’s rules and forms.

We carried out an evaluation, under the supervision and with the participation of our management, including our Chief Executive Officer (principal executive officer and principal financial officer), of the effectiveness of the design and operation of these disclosure controls and procedures, as such term is defined in Exchange Act Rule 13a-15(e), as of December 31, 2023. Based on this evaluation, the Chief Executive Officer concluded that our disclosure controls and procedures were effective as of December 31, 2023, the end of the period covered by this Annual Report on Form 10-K.

(b) Management’s Report on Internal Control over Financial Reporting

Management of the Company is responsible for establishing and maintaining adequate internal control over financial reporting as defined in Rules 13a-15(f) and 15d-15(f) under the Exchange Act.

Internal control over financial reporting is a process designed to provide reasonable assurance regarding the reliability of financial reporting and the preparation of financial statements for external purposes in accordance with U.S. generally accepted accounting principles. Because of its inherent limitations, internal control over financial reporting may not prevent or detect misstatements. Also, projections of any evaluation of effectiveness of internal control over financial reporting to future periods are subject to the risk that controls may become inadequate because of changes in conditions, or that the degree of compliance with the policies or procedures may deteriorate.

Our internal control over financial reporting is designed to provide reasonable assurance of achieving its objectives as specified above. Management does not expect, however, that our internal control over financial reporting will prevent or detect all error and fraud. Any control system, no matter how well designed and operated, is based upon certain assumptions and can provide only reasonable, not absolute, assurance that its objectives will be met. Further, no evaluation of controls can provide absolute assurance that misstatements due to error or fraud will not occur or that all control issues and instances of fraud, if any, within the Company have been detected.

Management, including our Chief Executive Officer, has assessed the effectiveness of our internal control over financial reporting as of December 31, 2023. In making our assessment of the effectiveness of internal control over financial reporting, management used the criteria set forth in Internal Control—Integrated Framework (2013) issued by the Committee of Sponsoring Organizations of the Treadway Commission (“COSO”).

As defined in SEC Regulation S-X, a material weakness is a deficiency, or combination of deficiencies, in internal control over financial reporting, such that there is a reasonable possibility that a material misstatement of the Company’s annual or interim financial statements will not be prevented or detected on a timely basis. Based on this assessment, management determined that, as of December 31, 2023, the Company’s internal control over financial reporting was effective.

There were no changes in our internal control over financial reporting that occurred during 2023 that have materially affected, or are reasonably likely to materially affect, our internal control over financial reporting.

During the three months ended December 31, 2023, none of our directors or officers adopted or terminated a “Rule 10-b5-1 trading arrangement” or “non-Rule 10-b5-1 trading arrangement” as each term is identified in Item 408 of Regulation S-K.

None.

PART III

Directors

The following table sets forth the names, ages, and positions with SINTX for each of our directors.

Our Board is divided into three classes (Class I, Class II and Class III) with staggered three-year terms. Directors in each class are elected to serve for three-year staggered terms that expire in successive years. Officers serve at the discretion of our Board. The following is information on the business experience of each director now serving and a discussion of the qualifications, attributes and skills that led to the Board of Directors’ conclusion that each one is qualified to serve as a director.

The following is a brief summary of the background of each of our directors:

Class III Directors— continuing directors with a term expiring at the 2026 annual meeting of stockholder.

B. Sonny Bal, M.D. has served on our Board of Directors since February 2012, as Chairman of our Board of Directors since August 2014 and as our President and Chief Executive Officer since October 2014. Dr. Bal was a tenured Professor in Orthopaedic Surgery at the University of Missouri, Columbia, and has an extensive history of research into silicon nitride ceramics. He was Adjunct Professor of Material Sciences at Missouri Science and Technology University at Rolla. Dr. Bal is a member of the American Academy of Orthopaedic Surgeons, the American Association of Hip and Knee Surgeons, and the International Society of Technology in Arthroplasty. Dr. Bal received his M.D. degree from Cornell University and an M.B.A. from Northwestern University, a J.D. from the University of Missouri, and a Ph.D. in Engineering from the Kyoto Institute of Technology in Japan. We believe that Dr. Bal’s breadth of experience and scientific expertise in silicon nitride qualifies him to serve as our Chairman, President and Chief Executive Officer.

Jeffrey S. White has served on our Board of Directors since January 2014. From January 2013 to 2018, Mr. White served as Principal at Medtech Advisory Group LLC, a firm he founded that advises early and mid-stage medical technology firms. In that capacity Mr. White has consulted MiMedx Group Inc., the leading amniotic tissue and allograft regenerative biomaterials firm since mid-2015 and served as Vice President, Product Management Strategies at MiMedix. Mr. White previously served as a director of Residency Select LLC, a company which offers psychometric assessment, training and compliance products to medical and surgical residency programs. Mr. White also served in 2014 and 2015 as President and director of Liventa Bioscience LLC, a provider of specialty amniotic tissue allografts for use in surgical and wound care applications. From May 2006 to December 2012 he served as Global Director of Business Development for Synthes Inc., a global orthopedic firm that was acquired by Johnson and Johnson in 2012. Mr. White has served as Chief Executive Officer and/or co-founder of several start-up surgical device firms and has previously held executive level positions at United States Surgical Corporation, now part of Medtronic. Mr. White holds a B.S. in Biology from Union College in Schenectady NY. We believe that Mr. White’s experience as an executive and founder of medical device companies qualifies him to serve on our Board of Directors.

Class II Directors — continuing directors with a term expiring at the 2025 annual meeting of stockholders.

David W. Truetzel has served on our Board of Directors since our acquisition of US Spine, Inc. in September 2010. Mr. Truetzel has been the general partner of Augury Capital Partners, a private equity fund that invests in life sciences and information technology companies, which he co-founded in 2006. Mr. Truetzel is a director of Enterprise Bank, Inc., Bonfyre, LLC, a provider of enterprise technology management solutions, Paranet, LLC, an IT services provider and ScholarPath, Inc. an educational software platform. Mr. Truetzel holds a B.S. in Business Administration from Saint Louis University and an M.B.A. from The Wharton School. We believe that Mr. Truetzel’s financial and managerial expertise qualify him to serve on our Board of Directors.

Eric A. Stookey has served on our Board of Directors since October 2014. Mr. Stookey has served as Chief Operating Officer of Osteoremedies, LLC since March of 2015. From October 2011 until August 2014, Mr. Stookey served as the President of the Extremities-Biologics division at Wright Medical Group Inc. Mr. Stookey also served in various other marketing and sales positions at Wright Medical Group Inc. since 1995, including as the Senior Vice President and Chief Commercial Officer from January 2010 to November 2011, as the Vice President North American Sales from 2007 to January 2010, as the Vice President US Sales from 2005 to 2007, as the Senior Director of Sales, Central Region, from 2003 to 2005 and as the Director of Marketing for Large Joint Reconstruction Products from 2001 to 2003. Mr. Stookey earned his M.B.A. from Christian Brothers University and his B.S. in Business from the Indiana University School of Business. We believe that Mr. Stookey’s industry and executive leadership experience qualifies him to serve on our Board of Directors.

Class I Director — continuing director with a term expiring at the 2024 annual meeting of stockholders.

Mark Froimson, M.D. has served on our Board of Directors since February 2019. Dr. Froimson is currently a Principal at Riverside Health Advisors, a consulting company that provides strategic advice and services to health care executive leaders. Dr. Froimson served as the President of the American Association of Hip and Knee Surgeons from March 2017 to March 2018. Previously, he was the Executive Vice President and Chief Clinical Officer of Trinity Health, a major national non-profit Catholic healthcare system comprising 93 hospitals in 22 states. Prior to his executive leadership position at Trinity Health, Dr. Froimson was President and Chief Executive Officer of Euclid Hospital, a Cleveland Clinic Hospital. Dr. Froimson served as a staff surgeon in the Department of Orthopedic Surgery at the Cleveland Clinic for over 16 years, during which time he held a variety of leadership positions, including President of the professional staff, Vice Chair of the Orthopedic and Rheumatologic Institute, and member of the board of governors and board of trustees. Dr. Froimson also serves on the board of directors of Pacira Biosciences, Inc., a publicly traded company on the NASDAQ Stock Market. Dr. Froimson received a B.S. in philosophy from Princeton University, an M.D. from Tulane University School of Medicine and an MBA from the Weatherhead School of Business at Case Western Reserve University.

Executive Officers

Our current executive officers and their respective ages and positions are as follows:

The following is a brief summary of the background of each of our executive officers.

B. Sonny Bal, M.D. has served on our Board of Directors since February 2012, as Chairman of our Board of Directors since August 2014 and as our President and Chief Executive Officer since October 2014. Dr. Bal was a tenured Professor in Orthopaedic Surgery at the University of Missouri, Columbia, and has an extensive history of research into silicon nitride ceramics. He was Adjunct Professor of Material Sciences at Missouri Science and Technology University at Rolla. Dr. Bal is a member of the American Academy of Orthopaedic Surgeons, the American Association of Hip and Knee Surgeons, and the International Society of Technology in Arthroplasty. Dr. Bal received his M.D. degree from Cornell University and an M.B.A. from Northwestern University, a J.D. from the University of Missouri, and a Ph.D. in Engineering from the Kyoto Institute of Technology in Japan. We believe that Dr. Bal’s breadth of experience and scientific expertise in silicon nitride qualifies him to serve as our Chairman, President and Chief Executive Officer.

David O’Brien has served as our Executive Vice President and Chief Operating Officer since July 2019. Mr. O’Brien previously served as the Company’s Vice President and General Manager from October 2016 to July 2019 and from March 2014 through September 2016, he held prior roles as our Vice President of Operations and Vice President of Manufacturing. Mr. O’Brien has over 30 years of experience in engineering, manufacturing, and operations leadership in advanced materials and medical device organizations. From 2005 to 2014, he fulfilled several engineering leadership roles for Covidien. From 1991 to 2005, he worked for Arnold Magnetic Technologies in the production of ceramic, powder metal and molded magnets in multiple facilities across the U.S. and in England. He has extensive experience with Lean and other Continuous Improvement initiatives. Mr. O’Brien holds an M.S. in Ceramic Engineering from the Georgia Institute of Technology, and a B.S. in Physics from the University of Texas at San Antonio.

Arrangements between Officers and Directors

To our knowledge, there is no arrangement or understanding between any of our officers and any other person, including directors, pursuant to which the officer was selected to serve as an officer.

Family Relationships

None of our directors are related by blood, marriage, or adoption to any other director, executive officer, or other key employees.

Other Directorships

With the exception of Dr. Froimson, who is also on the board of directors of Pacira Biosciences, Inc., a SEC public reporting company, none of the directors of the Company are also directors of issuers with a class of securities registered under Section 12 of the Exchange Act (or which otherwise are required to file periodic reports under the Exchange Act).

Other Involvement in Certain Legal Proceedings

None of our directors or executive officers has been involved in any bankruptcy or criminal proceedings (other than traffic and other minor offenses) or been subject to any of the items set forth under Item 401(f) of Regulation S-K, nor have there been any judgments or injunctions brought against any of our directors or executive officers during the last ten years that we consider material to the evaluation of the ability and integrity of any director or executive officer.

The Board and Committees

Our Board of Directors has five members. The Chairman of the Board and our Chief Executive Officer, B. Sonny Bal, MD, PhD, is a member of the Board and is a full-time employee of SINTX. David W. Truetzel, Eric A. Stookey, Jeffrey S. White, and Mark Froimson are non-employee directors, and the Board has determined that these persons (who constitute a majority of the Board) are “independent directors” under the criteria set forth in Rule 5605(a)(2) of the Nasdaq Listing Rules. The Board met seven (7) times during the year ended December 31, 2023. All directors attended more than seventy-five percent (75%) of the meetings of the Board and committee meetings of which such director was a member held during 2023.

In accordance with our restated Certificate of Incorporation, our Board of Directors is divided into three classes with staggered three-year terms. At each annual meeting of stockholders, the successors to the directors whose terms then expire will be elected to serve until the third annual meeting following such election. Our directors are divided among the three classes as follows:

Any additional directorships resulting from an increase in the number of directors will be distributed among the three classes so that, as nearly as possible, each class will consist of one-third of the directors.

Our Board of Directors has three permanent committees: the Audit Committee, the Compensation Committee, and the Corporate Governance and Nominating Committee. The written charters for these committees are on our website at https://ir.sintx.com/corporate-governance. Our Board of Directors may from time to time establish other standing committees. In addition, from time to time, special committees may be established under the direction of our Board of Directors when necessary to address specific issues.

The following table sets forth a description of the three permanent Board committees and the chairpersons and members of those committees, all of whom are independent directors:

Corporate Governance and Nominating Committee

The Corporate Governance and Nominating Committee is currently comprised of the following members: Eric A. Stookey (Chairman), David W. Truetzel and Jeffrey S White. Among other items, the Corporate Governance and Nominating Committee is tasked by the Board to: (1) identify individuals qualified to serve as members of the Board and, recommend individuals to be nominated by the Board for election by the stockholders or to be appointed by the Board to fill vacancies consistent with the criteria approved by the Board; (2) develop and periodically evaluate and recommend changes to SINTX’s Corporate Governance Guidelines and Code of Ethics, and to review the Company’s policies and programs that relate to matters of corporate responsibility, including public issues of significance to the Company and its stakeholders; and (3) oversee an annual evaluation of the performance of the Board. The Board has determined that each of the members of the Corporate Governance and Nominating Committee is “independent” under the standard set forth in Rule 5605(a)(2) of the Nasdaq Listing Rules. The Corporate Governance and Nominating Committee did not meet as a separate committee in 2023, but rather, because the committee is comprised of all three independent directors, governance matters were addressed as necessary in meetings of the Board. The Corporate Governance and Nominating Committee operates under a written charter adopted by the Board of Directors, which sets forth the responsibilities and powers delegated by the Board to the Corporate Governance and Nominating Committee.

Board Nominations

In considering Board candidates, the Board seeks individuals of proven judgment and competence who have strong reputations in their respective fields. Although we do not have a formal diversity policy, the Board considers such factors as experience, education, employment history, special talents or personal attributes, anticipated participation in Board activities, and geographic and diversity factors. The process for identifying and evaluating nominees would include detailed consideration of the recommendations and opinions of members of our Board, our executive officers, and our stockholders. There would be no difference in the process of evaluation of candidates recommended by a stockholder and those recommended by other sources.

The Nominating and Governance Committee has adopted a policy and procedures for shareholders to recommend nominees to the Company’s Board. The Committee will only consider qualified proposed nominees that meet the qualification standards set forth on Appendix A to the Committee’s charter available on the Company’s website at www.SINTX.com. Pursuant to the policy, only shareholders who meet minimum percentage ownership requirements as established by the Board may make recommendations for consideration by the Committee. At this time, the Board has set a minimum percentage ownership of 5% of the Company’s issued and outstanding shares of common stock for a period of at least one year. To make recommendations, a shareholder must submit the recommendation in writing by mail, courier or personal delivery to: Corporate Secretary, SINTX Technologies, Inc., 1885 West 2100 South, Salt Lake City, UT 84119. For each annual meeting the Committee will consider only one proposed nominee from each shareholder or shareholder group (within the meaning of Regulation 13D under the Exchange Act).

The recommendation must set forth (1) the name, address, including telephone number, of the recommending shareholder or shareholder group; (2) the number of the Company’s shares of common stock held by such shareholder and proof of ownership if the shareholder is not a holder of record; and (3) a statement that the shareholder has a good faith intention of holding the shares through the record date of the Company’s next annual meeting. For shareholder groups this information must be submitted for each shareholder in the group.

The recommendation must set forth in relation to the proposed nominee being recommended by the shareholder: (1) the information required by Items 401, 403 and 404 of Regulation S-K under the Exchange Act, (2) any material relationships or agreements between the proposed nominee and the recommending shareholder or the Company’s competitors, customers, labor unions or other persons with special interests in the Company; (3) a statement regarding the qualifications of the proposed nominee to serve on the Board; (4) a statement that the proposed nominee can fairly represent the interests of all shareholders of the Company; and (5) a signed consent by the proposed nominee to being interviewed by the Nominating and Governance Committee.

Recommendations must be made not later than 120 calendar days prior to the first anniversary of the date of the proxy statement for the prior annual meeting of shareholders. In the event that the date of the annual meeting of shareholders for the current year is more than 30 days following the first anniversary date of the annual meeting of shareholders for the prior year, the submission of a recommendation will be considered timely if it is submitted not earlier than the close of business on the 120 days prior to such annual meeting and not later than the close of business on the later of 90 days prior to such annual meeting or the close of business 10 days following the day on which public announcement of the date of such meeting is first made by the Company.

Audit Committee

We have a standing Audit Committee and audit committee charter, which complies with Rule 10A-3 of the Exchange Act, and the requirements of the Nasdaq Listing Rules. Our Audit Committee was established in accordance with Section 3(a)(58)(A) of the Exchange Act. The Audit Committee is currently comprised of the following members: David W. Truetzel (Chairman), Eric A. Stookey and Jeffrey S White. The Audit Committee provides oversight for financial reporting matters, internal controls, and compliance with the Company’s financial policies, and meets with its auditors when appropriate. The Audit Committee did not meet as a separate committee in 2023, but rather, because the committee is comprised of all three independent directors, committee matters were addressed as necessary in meetings of the Board. The Board has determined that David W. Truetzel is an “audit committee financial expert” within the meaning of Item 407(d)(5) of Regulation S-K. Further, the Board has determined that each of David W. Truetzel, Jeffrey S. White and Eric A. Stookey are “independent” under the standard set forth in Rule 5605(a)(2) of the Nasdaq Listing Rules. The Audit Committee operates under a written charter adopted by the Board of Directors, which sets forth the responsibilities and powers delegated by the Board to the Audit Committee.

Compensation Committee

The Compensation Committee of the Board is comprised of the following members: Jeffrey S. White, (Chairman), David W. Truetzel and Eric A. Stookey. The Board has determined that each of David W. Truetzel, Jeffrey S. White and Eric A. Stookey are “independent” under the standard set forth in Rule 5605(a)(2) of the Nasdaq Listing Rules. The Compensation Committee recommends to the Board for determination compensation of our executive officers, including the chief executive officer, and addresses salary and benefit matters for other key personnel and employees of the Company. The Compensation Committee did not meet as a separate committee in 2023, but rather, because the committee is comprised of all three independent directors, committee matters were addressed as necessary in meetings of the Board. The Compensation Committee operates under a written charter adopted by the Board of Directors, which sets forth the responsibilities and powers delegated by the Board to the Compensation Committee.

Code of Business Conduct

The Board has adopted a Code of Business Conduct that applies to all of our employees, officers and directors, including those officers responsible for financial reporting. The code of business conduct is available on our website at https://ir.sintx.com/corporate-governance. We intend to disclose any amendments to the code or any waivers of its requirements on our website.

The Bylaws of the Company provide that no contract or transaction between SINTX and one or more of its directors or officers, or between SINTX and any other corporation, firm, association, or other organization in which one or more of its directors or officers are financially interested, shall be void or voidable solely for this reason, or solely because the director or officer is present at or participates in the meeting of the Board of Directors or committee that authorizes or approves the contract or transaction, or because their votes are counted for such purpose, provided that:

The following discussion relates to the compensation of our “named executive officers.”

Summary Compensation Table

The following table sets forth information about certain compensation awarded or paid to our named executive officers for the 2023 and 2022 fiscal years.

(1) Amount reflects matching of 401(k) contributions paid by us, unless otherwise noted.

Narrative Disclosure to Summary Compensation Table. We do not have written employment agreements with any of our executive officers. All of our executive officers serve on an at-will basis. The base salaries for our named executive officers were determined by our compensation committee after reviewing a number of factors, including: the responsibilities associated with the position, the seniority of the executive’s position, the base salary level in prior years, and our financial position; and for executive officers other than our Chief Executive Officer, recommendations made by our Chief Executive Officer. The Board, on an annual basis, adopts an executive bonus payment plan that is designed to provide executive officers with annual incentive compensation based on the achievement of certain pre-established performance objectives. By utilizing a combination of objective and subjective performance factors critical to our success, this program incentivizes our executive officers to achieve results that benefit them and the Company. Performance factors include the achievement of predetermined financial performance objectives, adherence to financial discipline measures and achievement of business development, product development and long-term business stability. The Board may modify or re-weight the objectives during the course of the fiscal year, if necessary, to reflect changes in our business plan.

Outstanding Equity Awards at Fiscal Year-End

The following table shows information regarding equity awards held by our named executive officers as of December 31, 2023:

401(k) Plan

We offer our executive officers, including our named executive officers, retirement benefits, including participation in our tax-qualified profit sharing plan that includes a “cash-or-deferred” (or 401(k)) feature in the same manner as other employees. The plan is intended to satisfy the requirements of Section 401 of the Internal Revenue Code. Our employees may elect to reduce their current compensation by up to the statutorily prescribed annual limit and have a like amount contributed to the plan. In addition, we may make discretionary and/or matching contributions to the plan in amounts determined annually by our Board. We currently elect to match the contributions of our employees who participate in our 401(k) plan as follows: a match of 100% on the first 3% of compensation contributed by a plan participant and a match of 50% on amounts above 3%, up to 5%, of compensation contributed by a plan participant.

Potential Payments upon Termination or Change in Control

We had entered into certain agreements and maintained certain plans that may have required us to make certain payments and/or provide certain benefits to the executive officers named in the Summary Compensation Table in the event of a termination of employment or change in control.

Pursuant to severance agreements that we have entered into with each of our named executive officers, upon the consummation of a change in control, all outstanding options, restricted stock and other such rights held by the executives will fully vest. Additionally, if a change in control occurs and at any time during the one-year period following the change in control (i) we or our successor terminate the executive’s employment other than for cause (but not including termination due to the executive’s death or disability) or (ii) the executive terminates his employment for good reason, then such executive has the right to receive payment consisting of a lump sum payment equal to two times his highest annual salary with us during the preceding three-year period, including the year of such termination and including bonus payments (measured on a fiscal year basis), but not including any reimbursements and amounts attributable to stock options and other non-cash compensation. “Change in control” is defined in the severance agreements as occurring upon: (i) any “person” (as such term is used in Sections 13(d) and 14(d) of the Exchange Act) becoming the “beneficial owner” (as defined in Rule 13d-3 under the Exchange Act), directly or indirectly, of securities representing 50% or more of the total voting power represented by our then outstanding voting securities (excluding securities held by us or our affiliates or any of our employee benefit plans) pursuant to a transaction or a series of related transactions which our Board did not approve; (ii) a merger or consolidation of our company, other than a merger or consolidation which would result in our voting securities outstanding immediately prior thereto continuing to represent at least 50% of the total voting securities or such surviving entity or parent of such corporation outstanding immediately after such merger or consolidation; or (iii) the approval by our stockholders of an agreement for the sale or disposition of all or substantially all of our assets. As defined in the severance agreements, “cause” means: (i) the executive’s commission of a felony (other than through vicarious liability or through a motor vehicle offense); (ii) the executive’s material disloyalty or dishonesty to us; (iii) the commission by the executive of an act of fraud, embezzlement or misappropriation of funds; (iv) a material breach by the executive of any material provision of any agreement to which the executive and we are party, which breach is not cured within 30 days after our delivery to the executive of written notice of such breach; or (v) the executive’s refusal to carry out a lawful written directive from our Board. “Good reason” as defined in the severance agreements means, without the executive’s consent: (i) a change in the principal location at which the executive performs his duties to a new work location that is at least 50 miles from the prior location; or (ii) a material change in the executive’s compensation, authority, functions, duties or responsibilities, which would cause his position with us to become of less responsibility, importance or scope than his prior position, provided, however, that such material change is not in connection with the termination of the executive’s employment with us for any reason.

In the event that an officer entitled to receive or receives payment or benefit under the severance agreements described above, or under any other plan, agreement or arrangement with us, or any person whose action results in a change in control or any other person affiliated with us and it is determined that the total amount of payments will be subject to excise tax under Section 4999 of the Internal Revenue Code, or any similar successor provisions, we will be obligated to pay such officer a “gross up” payment to cover all taxes, including any excise tax and any interest or penalties imposed with respect to such taxes due to such payment.

Code of Business Conduct Violations

It is our policy under our Code of Business Conduct to take appropriate action against any executive officer whose actions are found to violate the Code or any other policy of SINTX. Disciplinary actions may include immediate termination of employment and, where SINTX has suffered a loss, pursuing its remedies against the executive officer responsible. SINTX will cooperate fully with the appropriate authorities where laws have been violated.

Role of the Board in Risk Oversight

Risk is inherent with every business, and how well a business manages risk can ultimately determine its success. Management is responsible for the day-to-day management of the risks that we face, while our Board of Directors, as a whole and through its committees, has responsibility for the oversight of risk management. In its risk oversight role, our Board of Directors is responsible for satisfying itself that the risk management processes designed and implemented by management are adequate and functioning as designed.

Our Board of Directors does not have a standing risk management committee, but rather administers this oversight function directly through our Board of Directors as a whole, as well as through various standing committees of the Board of Directors that address risks inherent in their respective areas of oversight. In particular, our Board of Directors is responsible for monitoring and assessing strategic risk exposure, including a determination of the nature and level of risk appropriate for us. Our Audit Committee has the responsibility to consider and discuss our major financial risk exposures and the steps our management has taken to monitor and control these exposures, including guidelines and policies to govern the process by which risk assessment and management is undertaken. The Audit Committee also monitors oversight of the performance of our internal audit function. Our Corporate Governance and Nominating Committee monitors the effectiveness of our corporate governance guidelines, including whether they are successful in preventing illegal or improper liability-creating conduct. Our Compensation Committee assesses and monitors whether any of our compensation policies and programs have the potential to encourage excessive risk-taking or promote behaviors contra to our Code of Business Conduct.

Board Compensation

The following table shows the total compensation paid or accrued during the fiscal year ended December 31, 2023 to each of our non-employee directors.

The following compensation schedule sets forth compensation for non-employee directors (paid on a quarterly basis) as approved by the Board: